Wayne Dalton Model 3018 Garage Door Opener

Share This Post

Garage Door Does Not Open Or Close Fully No Light Flashes

Wayne Dalton ClassicDrive 3018 -TheGarageDoorGeek /2

When you operate your Wayne Dalton garage door opener, and the door doesnt open or close fully, then you need to adjust the travel limits. Here is why.

The travel limit of a garage door opener refers to the distance the door has to travel to fully open or close. When the garage door does not fully close, and the light does not flash, it means the opener assumes the door is fully opened/closed, and no error was detected. This is why you have to increase the travel limit to fix the problem.

Here is how to increase the travel adjustment for Wayne Dalton drives:

To increase the close travel adjustment,

  • Using the remote or wall control, open the door to its fully open position
  • Turn the close adjustment clockwise with a flat screwdriver, to about ¼ turn
  • Close the door with the remote or wall control. The garage door should reach the floor with the bottom seal compressed a little
  • If the door reverses once it reaches the floor, reduce the travel limit.
  • At this point, you need to adjust it till it touches the floor and compresses the door seal without reversing.

    To increase the open travel adjustment.

  • First, disconnect the garage door opener from the door
  • Manually open the garage door to its fully open position. Take note of the location where the garage door is fully opened
  • Reconnect the garage door to the opener
  • Adjust the open travel adjustment and then open the door with the remote.
  • Keep tweaking till the garage door fully opens.
  • Check The Power Supply To The Garage Door Opener

    Disconnect your Wayne Dalton opener from the socket-outlet and plug another device in the socket to see if it works. Also, check the power cable from the garage door opener for any signs of damage. When there is a break in the cable, your opener will not have power. Check the circuit breaker or fuse for the garage. If it has tripped open, then switch it back on.

    Common Issues With Wayne Dalton Garage Doors

    Wayne Dalton doors are generally reliable, though there are a few parts that tend to wear down more quickly than others. We often get calls to fix Wayne Dalton springs or tracks, which often means your garage door gets stuck while opening or closing.

    Other common issues include:

    • Damaged garage door panels due to weather or vehicle mishaps
    • Garage doors falling off the track
    • Jammed tracks, pulleys, or springs
    • Misaligned doors
    • Damaged springs, frames, and tracks
    • Lack of lubrication
    • Garage door doesnât close all the way
    • Noisy garage doors

    Our technicians arrive with fully stocked trucks so they can resolve almost any garage door issue on the first visit. However, if your issue requires a full garage door replacement or overhaul, we may need to order a new door and come back to install it.

    Read Also: Townhomes With Garages For Rent

    How To Program The Quantum And Classic Drive To A Wireless Wall Station

    Before you program the Wireless Wall Station to the garage door opener, its a crucial step to change the security code on the wall station. This is an effortless process and will take less than two minutes. Here is how to do it.

    Changing the security code on a Wireless Wall Station

  • Press and hold the wall stations light button for about 10 seconds, until the LED on the device starts blinking
  • Release the button. The LED should go off
  • Once again, press and hold the light button. The LED will turn on for about 5 seconds and then blink again.
  • Release the button. The LED will blink three times. That indicates that the programming is successful
  • Now that youre done changing the code on the Wireless Wall Station, you can go ahead and program it to the Quantum garage door opener.

    Programming the Quantum or Classic Drive Opener to a Wireless Wall Station

  • Press the Program Switch on the side of your garage door opener. A red LED, as well as the overhead light on the garage door opener, will turn and stay on. You have one minute to complete the next step
  • Press the light on/off button on the Wireless Wall Station. The red LED should blink three times. This means the wall station is successfully configured to work with your opener.
  • Press the light on/off button one more time to confirm. You should be able to operate the garage door opener with the wall station now.
  • Check For Any Obstruction

    Wayne Dalton Garage Door Opener Model 3018 Manual

    These are the two main things that can hinder your Wayne Dalton garage door opener from opening the door. These are seen as an obstruction.

  • Imbalanced garage door
  • Damaged garage door tracks or rollers
  • Now here is how to check for any obstruction in the door.

    • First, disconnect the garage door opener from the garage door by pulling the emergency cord.
    • Slowly lift the garage door manually and pay attention to the areas where the door binds or sticks
    • Inspect the garage door tracks and rollers where the door sticks for any signs of damage. Fix any dent on the tracks and replace any worn out if you can. Else call a garage door technician.
    • When the garage door gets opened about halfway, let it go
    • If it is properly balanced, the garage door should stay in that position without dropping. If thats not the case, then the garage door needs to be balanced. Call a garage door technician to balance the door for you.

    Also Check: Ford’s Garage Menu St Augustine

    Wayne 3018 User Manual

    Models: 3014, 3018, 3018DLX & 3514

    Automatic Garage Door Opener

    For Sectional Overhead Residential Doors Only

    DO NOT USE ON ONE PIECE DOORS

    CONTENTS

    Infrared Safety Sensor Obstruction Test

    Installing Infrared Safety Sensors 15

    Trouble

    Wall Station Code Change & Programming

    Parts Breakdown – Power Head Assembly And Accessories

    Transmitters Code Change & Programming

    DOOR AND OPENER WILL NOT OPERATE PROPERLY UNTIL INFRARED SAFETY

    SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE DOOR

    OPENER UNTIL FULLY INSTALLED, ADJUSTED & INSTRUCTED TO DO SO!

    READ THE ENCLOSED INSTRUCTIONS CAREFULLY BEFORE

    INSTALLING/OPERATING THIS OPENER! PAY CLOSE ATTENTION TO ALL

    WARNING LABELS AND NOTES. THIS MANAUL SHOULD BE ATTACHED IN

    CLOSE PROXIMITY TO THE GARAGE DOOR OPENER.

    Garage Door Opener Not Working

    This is not a common problem, but it does happen sometimes. If you Wayne Dalton garage door opener is not responding to command from the wall station or the remote control, a couple of things can be the cause.

    • Garage door opener has no power
    • Remote control or wall station is not programmed
    • The motor protector has tripped open due to excessive heat

    Follow these troubleshooting steps if your garage door opener is not working.

    Read Also: Garage Door Insulation Lowe’s

    What Can A Smart Garage Door Opener Do

    • Use your smartphone to remotely control your garage door or gate via Wi-Fi or over the Internet.
    • Control your garage door or gate with real time video.
    • Check if your garage door or gate is open or closed.
    • Use Apple HomeKit, Amazon Alexa, Google Home, IFTTT or Samsung SmartThings to operate the garage door or gate.
    • Check who opened or closed the garage door or gate.
    • Use your Apple Watch and Siri Shortcuts to operate the garage door or gate.
    • Manage your garage door or gate access remotely by user, time, door and also by location.
    • Open the garage door or gate automatically when you arrive to your home .
    • Schedule when the garage door or gate should automatically open and close.

    Wayne Dalton Classicdrive Garage Door Opener Manual

    Wayne Dalton Classicdrive model 3018

    Installation instructions, troubleshooting guide and owners manual for the Classic Drive garage door openers, models 3018, 3018DLX, 3522 and 3522DLX.

    Please wait while the file is being retrieved

    Privacy Overview

    Cookie
    cookielawinfo-checkbox-analytics 11 months This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category “Analytics”.
    cookielawinfo-checkbox-functional 11 months The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category “Functional”.
    cookielawinfo-checkbox-necessary 11 months This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category “Necessary”.
    cookielawinfo-checkbox-others 11 months This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category “Other.
    cookielawinfo-checkbox-performance 11 months This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category “Performance”.
    viewed_cookie_policy 11 months The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.

    You May Like: Chamberlain Garage Door Remote Opener

    Page : Package Contents

  • Page 3 PRE-INSTALLATION INSPECTION OF YOUR GARAGE DOOR PRIOR TO CLASSICDRIvE OPENER INSTALLATION ® To ensure your new Classicdrive opener works as intended, your garage door must be ® properly installed and balanced. Before installing your garage door opener, open and close you door manually to ensure it operates smoothly from top to bottom.
  • Page 4 pre-Installation IMportant! Before starting the installation read these instructions thoroughly to familiarize yourself with all aspects of installation and adjustment. IMportant: IF yOuR GARAGE HAS NO SERVICE ENTRANCE DOOR, INSTALL AN OPTIONAL OuTSIDE quICK RELEASE LOCK. THIS ACCESSORy ALLOWS MANuAL OPERATION OF GARAGE DOOR FROM OuTSIDE IN CASE OF POWER FAILuRE. IdentIFy your door Identify your door by referring to illustrations below and verify that your door type is a sectional door with curved track.
  • Cold Weather Garage Door Opener

    Cold Weather Garage Door Opener. cold weather especially can affect your garage door since it’s outside. In the cold, your garage door opener may strain to open the door, which could create greater energy costs to you or cause the garage door or opener to break.

    If the garage door makes a loud squeaking or grinding noise, the problem may be with the rollers. Updated 3/24/2022 as you may realize, cold weather affects garage doors and openers in many ways. Or, the garage door opener may not be able to open the door at all.

    Don’t Miss: Remote For Garage Door Opener

    Page 3: Programming For Homelink To Classicdrive

  • Page 36 alternate programming for homelink to the classicdrive ®® note: This Step can only be done on automobiles equipped with the programming/training homelink unit ® warnIng HomeLink System. ® GARAGE DOOR MAy OPERATE DuRING PROGRAMMING. TO AVOID note: Programming HomeLink requires a Wayne-Dalton ®…
  • Page 37 adjustments adjustment # 1 opening and closing Force adjustment # 2 contact obstruction sensing This garage door opener is built with a safety system that allows the door to reverse when closing and stop when opening. This must be The opener is designed to automatically reverse the door during adjusted so your opener does not use excessive force in the down direction or react to the weight of the door during upward travel.
  • How To Program The Quantum Garage Door Opener With A Transmitter

    Wayne Dalton Garage Door Opener Model 3018 Manual

    Follow these simple steps to program a remote transmitter to work with your Quantum Garage Door Opener.

  • Press the Program Switch on the side of your garage door opener. A red LED and the overhead light on the garage door opener, will turn and stay on. You have one minute to complete the next step
  • Press the button on the remote youll like to operate your opener with. The red LED should blink three times. This means the wall station is successfully configured to work with your opener.
  • Press the same button on the remote one more time to confirm. You should be able to operate the garage door opener with the wall station now.
  • Also: Wayne Dalton Garage Door Parts: Complete List

    Also Check: Used Metal Garages For Sale

    Programming The Keyless Entry Keypads

  • Find the program button on the right side near the back of the motorhead. This usually has a red LED light above it.
  • To avoid causing any programming failure, ensure you do this when you are six feet away from the opener.
  • You will be required to put in a five-digit pin and to ensure you stay safe. A quick tip: do not use your address as the pin as this is an easy guess.
  • If you want to know that the programming is complete, the LED light will blink thrice once you enter the pin.
  • Door Fully Opens Opener Light Flashes

    When your Wayne Dalton garage door openers light flashes after the door reach the fully open position, it means the open travel adjustment is set too high, and you have to reduce.

    Follow the steps outlined earlier on how to increase the open travel adjustment, but this time reduce it.

    Recommended Posts

    Also Check: Garage Doors Roll Up Residential

    Programming The Idrive Garage Door Opener

    Something worth knowing is the iDrive garage door opener can be controlled with up to six devices at a time. The devices can be a combination of several remote controls, a Wall Station, or Keyless Entry pads. If, for some reason, you program a new device, which happens to be the seventh device, the opener will automatically erase the first device programmed from its memory.

    Follow these steps to program a device to work with your iDrive garage door opener.

  • Close the garage door and pull the emergency handle to disconnect the opener from the door.
  • Press the Red Program button on the garage door opener. This can be found on the front cover of the opener. The opener will beep to indicate that you are programming mode. Now you have up to 30 seconds to complete the next step
  • Press and hold your desired button on the remote or wall station for operating the opener till you hear a beep again. This indicates that the iDrive garage door opener is programmed successfully. If you dont hear any beep, repeat steps 1 to 3.
  • Reconnect the garage door opener to the door
  • Now press the same button on the remote or wall station to see if the garage door opener activates.
  • Keep in mind that the first activation will not open or close the garage door fully. It will go up or down about six-inch. It will operate correctly on the second activation

    Also: Wayne Dalton Garage Door Opener Troubleshooting: Step by Step Guide

    Wayne Dalton Garage Door Repair Vs Replacement

    Garage Door Opener Troubleshooting-Wayne Dalton Opener Not Closing

    While some issues with Wayne Dalton garage doors can be repaired, others may require a replacement. With our 25-point safety inspection, we assess the situation and tell you exactly what you need. We carry the highest quality parts and we fix it right the first time.

    Here are the most common reasons your garage door canât be repaired and may need to be replaced:

    • Your garage door has suffered structural damage. This could be caused by weather-related incidents, vehicle damage, or another traumatic event.
    • Repairs would cost more than a full replacement. If it costs more to maintain your current door than it would to replace it altogether, we can install a new garage door with long-lasting components.
    • Your doors security has been compromised. We recommend a replacement if youâve experienced a break-in or other garage door-related event that affects your security, safety, or quality of life.

    If you need a garage door replacement or overhaul, we can provide guidance on your options and give a free new door estimate.

    You May Like: Universal Garage Door Opener Lowes

    After Installing Remootio You’ll Be Able To:

    • Use your smartphone to control your garage door via Bluetooth, Wi-Fi or over the Internet.
    • Check if your garage door is open or closed.
    • Use Amazon Alexa, Google Home or Samsung SmartThings to operate the garage door.
    • Check who opened or closed the garage door.
    • Use your Apple Watch and Siri Shortcuts to operate your garage doors.
    • Send virtual keys to your family, friends, guests or your gardener and revoke their access rights anytime.
    • Open the garage door automatically as you arrive home .
    • Schedule when the garage door should automatically open and close.

    In The Cold Your Garage Door Opener May Strain To Open The Door Which Could Create Greater Energy Costs To You Or Cause The Garage Door Or Opener To Break

    Beside above, why does my garage door only go halfway up? does cold weather affect a garage door opener? Or, the garage door opener may not be. What usually happens is that your garage door will go up without any problems, but when you push the button again, it will only go down a few inches and then go right back up, maybe you try this for several time and finally goes down to the floor. When you properly lubricate your garage door opener, you minimize the strain on. The more you know going in, the more prepared youll be to handle them. For this reason, the garage door wont close when it is cold. Before winter approaches, you have time to take precautions. Garage door openers can lose some of their lubrication in cold weather, which may cause them to work harder.

    Also Check: Average Cost To Replace Garage Door

    Or The Garage Door Opener May Not Be Able To Open The Door

    Do not try to force open a frozen door, as this can break the weather. If the door feels heavy when you try to raise it manually, its often a sign of a worn spring. cold weather especially can affect your garage door since it’s outside. Whether your door is a 7×7 single door or a 15×7 double door, the use of this excellent bu400 centurion brings a quiet and smooth operation for the garage door functioning. If water pools and freezes at the base of the garage door, it can freeze the door shut. 1 top 7 best garage door lubricant for cold weather. Water melts and freezes very often, causing ice formation underneath your door. Three effects of cold weather on garage door openers are: These precautions will prevent any damage to the garage door and manage to keep it quiet.

    Source: dunmiresgaragedoors.com

    If the door feels heavy when you try to raise it manually, its often a sign of a worn spring. Or, the garage door opener may not be able to open the door.

    Source: www.aaagaragedoor.com

    does cold weather affect a garage door opener? What usually happens is that your garage door will go up without any problems, but when you push the button again, it will only go down a few inches and then go right back up, maybe you try this for several time and finally goes down to the floor.

    Source: garageviews.blogspot.com

    Related Posts