Reset Genie Garage Door Opener

Share This Post

How To Reset A Garage Door After Opening It Manually

Reset a Genie Garage Door Opener – Genie Intellicode

An automatic garage door opener is a wonderful, energy and back saving tool. At the click of a button, your door opens and you can drive your car in or out of the garage. If you are using the garage as a workshop, you can open the door just a little for ventilation.

There may be times that you want to disengage the automatic opener and use the garage door manually. This may be due to a power outage or just wanting to open the door a few inches and no more. Resetting the door is something that can be confusing. By following these steps, you can reset your garage door quickly and without fuss.

It is only safe to put your garage door in manual mode when it is in the down position. If you experience a lose of power while your door is in the up position, please call your local Overhead Door Company.

To manually open most garage doors, you simply pull a corded handle that is attached to the door. This disengages the electric drive from the door and you can manually open and close it. To reset it, begin by pulling the cord in the opposite direction. It should click in place. Once this happens, you can open and close the door electronically. matches homeowners and businesses with local companies specializing in garage door repairs. We have implemented a thorough screening process to ensure we connect homeowners and businesses with top quality garage door repair companies on our website.

How To Connect A Genie Garage Door Opener To Iphone

You can connect the opener to iPhone using the Aladdin Connect System. It is a convenient mobile device app to operate up to 20 garage door openers from anywhere. To connect:

  • Start by checking the Wi-Fi signal. If weak or no signal, move the Wi-Fi router closer to the garage or try installing a Wi-Fi range extender.
  • Follow the app instructions to create an account, set up the opener, add users, and set rules and notifications.
  • Place include the unintended operation warning placard next to the garage door openers wall button.

How To Reset A Genie Garage Door Opener

This article was co-authored by Barry Zakar and by wikiHow staff writer, . Barry Zakar is a professional handyman and the founder of Little Red Truck Home Services based in the San Francisco Bay Area. With over ten years of experience, Barry specializes in a variety of carpentry projects. He is skilled at constructing decks, railings, fences, gates, and various pieces of furniture. Barry also holds his MBA from John F. Kennedy University.There are 8 references cited in this article, which can be found at the bottom of the page. This article has been viewed 222,617 times.

Genie garage doors are known for their convenience and easy-to-use remotes. Unfortunately, this system becomes less simple when you need to sync or resync your remote. If you have a wireless keypad, you may also need to recalibrate this device if it doesnt open your garage door properly. With the push of a few buttons, you can reset either your Genie opener or wireless keypad in a matter of minutes.

Read Also: Apartment With Garage For Rent

How Do I Reset My Genie Garage Door Sensor

The Safe-T-Beam are safety sensors on the Genie garage door opener that shine an invisible infrared beam across the garage door. The system is being obstructed during the closing cycle and automatically reverses the garage door to the fully open position.

Obstructions could be anything from your kids arm to dirt on the tracks, magnetic garage door decorations, or a stray cable powering your Christmas decorations.

The LED lights on both sensors will have a steady glow when installed and aligned correctly. The red light on the sending sensor will always glow regardless of alignment as long as it receives power. However, if the green light on the receiving sensor is dim, flickers, or off, alignment is necessary. Follow the steps below.

  • Remove the receiving sensor from the bracket by tasking off the fastening nuts.
  • Face the sensor away from the sensor, and the light will turn off.
  • Wait for 10 seconds, and slowly turn the sensor back to its position. Align the sensor with the sending sensor until the green light glows steadily. Insert the sensor into the bracket, readjust it and then tighten the screws.
  • Press the wall control button, and the garage door should close completely.

Do Garage Door Openers Have Fuses

Genie Screw Drive Garage Door Opener Reset :: automationsoftgo

A garage door opener is a combination of various features that allow the product to function properly. Depending on the model or brand you own, it might include a fuse on its list of parts. This component is an essential part of inspecting if your garage door opener is malfunctioning.

A fuse is an essential part of an electrical circuit. To put it simply, this safety feature is what protects your garage opener if theres something faulty within the circuit. The fuse has a small wire inside that will melt and break the circuit if theres too much electric current passing through.

There are a few ways to tell if a fuse in your garage opener has burned out:

  • Your circuit breaker is on.
  • Your garage opener has no power, but the system is plugged into an outlet.
  • You know the outlet the system is plugged into has power.

Either the fuses or another internal component is likely the cause of your faulty garage opener. Its best to consult a professional technician if you suspect an issue is occurring with your garage opener. This way, you wont encounter any safety issues. If the fuse is your concern, the technician will check to see if its still operating by:

  • Locating the glass fuse
  • Inspecting if the fuse has blown
  • Using proper tools to check its performance
  • Replacing the fuse if needed

Also Check: Craftsman Garage Door Opener 1/2 Hp

How To Program Genie Garage Door Opener

Before programming the opener, there are several important things to note:

  • Check to make sure that there are no objects in the garage door opening.
  • The door must be locked to the opener prior to programming.
  • The door should rest somewhere between full open and closed. Do not start with the door fully open or closed.

The order of programming the openers functional settings and install any accessories should strictly be as follows:

  • Down Travel Limit
  • Install Battery Backup
  • Why Reset Your Garage Door Opener Keypad

    If you have a Liftmaster garage door opener or another newer type of system, youll have a garage door keypad that allows you to gain entrance into your garage with a code when you dont have the garage remote. The garage door keypad code is an easy way for your entire family to enter the garage. Even if youre the only one who has the remote openers, your kids or other family members will still be able to gain entry into the garage.

    While a garage door code is convenient, its helpful to learn how to reset the code when necessary. You may want to reset your code if you:

    • Lose your remote
    • Move into a new place
    • Give the garage code to someone who doesnt live in your home
    • Suspect suspicious activity in your neighborhood
    • Think someone has attempted to gain access into your garage
    • Cant remember your old code

    Most of the newer garage door openers have a keypad on the inner side of your garage door system. Its helpful to check your keypad to ensure its working correctly and has batteries so you can move forward with the programming process.

    Don’t Miss: Universal Garage Door Opener Menards

    Accessing The Garage Door Motor

  • 1Set up a ladder beneath the garage door motor in your garage. The garage door motor is a roughly 8 in × 5 in box mounted to the roof of your garage. Open the ladder by pulling the 2 metal halves apart from each other and pressing down on the 2 cross-beams. Then, climb up the ladder until you can comfortably reach the garage door motor.XResearch source
  • If you dont have a ladder, purchase one from a hardware store or a home improvement store. Or, borrow one from a friend.
  • 2Open the panel on the left side of the motor unit. If youre standing in front of your garage door and looking at the motor unit, the left-hand light compartment doubles as a panel covering the units controls. Pull firmly down on this panel until it comes away from the motor unit. The hinges at the bottom of the panel will allow it to swivel down without falling.XResearch source
  • The panel placement may differ from one style of unit to the next. The panel may also be located at the back or side of the garage door motor box.
  • 3Locate the Learn button at the front of the control panel. Once youve lowered the light panel out of the way, youll see a series of warnings and safety information, a light bulb, and a small control panel. Look over the control-panel area until you spot a small button labeled Learn. The button will only be about 12 inch in diameter.XResearch source
  • Depending on the make and model of your garage door opener, the button may be yellow and round or purple and square.
  • Genie Garage Door Opener Keypad Not Working

    How To Reset Your Genie Garage Door Opener If You Lose Your Keypad PIN Code

    Here is how to troubleshoot a keypad that stops working with your garage door opener.

    • Make sure you are putting in the correct PIN.
    • Check the emergency released rope is not activated. The garage door will not respond to the keypad if it is in manual mode. Disengage the emergency release rope and input the PIN to operate the garage door.
    • Check the batteries in your opener keypad and replace them.
    • Check for stuck keys. Dust and grime accumulate in between the keypad buttons, causing them to get stuck. Clean the keypad with a dry toothbrush. If the keypad is too damaged, you will have to replace it.
    • Inspect the keypad for any damage. Over time, weather, humidity, and contact can damage the keypad preventing it from working. Replace the keypad if necessary.
    • Open the keypad and look for frayed or damaged wires. Then, reattach the cables and make sure they are secure or replace them.
    • If the opener still refuses to respond to the keypad, reset it and reprogram it to the opener with a new PIN.

    Recommended Reading: Craftsman Garage Door Opener Not Working

    Lets Adjust A Genie Garage Door Opener

    Genie garage door opener travel limits are programmable. This allows you to set the distance your door can travel up or down. If the limits arent adjusted properly then the door wont close or open completely.

    If this happens and your door opens partially then you need to adjust the up travel limit. If the opposite happens, which is the door not closing entirely then do the opposite. The down travel limit here has to be adjusted.

    Genie garage door openers are also incredibly easy to transport. So dont be concerned about the additional expense of relocating your garage.

    So, how can you get your Genie garage door opener to work properly? To do so, youll need to follow a few basic steps.

    Without further ado, lets get started-

    Linking A New Garage Door Opener

  • 1Pull off the bulb cover to expose the motor units control panel. Pry off the bulb cover that covers up the units safety warnings and control panel. If your bulb unit has release tabs on the top right and left corners, press those and then pull down on the bulb panel.XResearch source
  • Different models of Liftmaster motor units may have the control panel on the back, left, or right.
  • 2Press the Learn button until the LED light comes on. The Learn button should be in the top-right corner of the motor units small control panel. Press it down 1 time and dont hold it. Youll see a small LED light illuminate. This lets you know that the motor unit is ready to receive a radio signal from the remote unit.XResearch source
  • If you have large fingers and cant push the small Learn button, press it with the tip of a pen instead.
  • 3Hold down a button on your remote garage door opener. Within 30 seconds of pressing the Learn button, press down on a button on the remote. This will send out a radio signal to the ceiling-mounted motor unit. In the future, when the unit receives that specific signal, it will open the garage door its attached to.XResearch source
  • On most Liftmaster units, the light attached to the motor unit will light up for 1/2 a second to indicate that the remotes button has been linked.
  • Be careful not to press a button that youve already linked to another garage door! If you do, pressing the button will open both doors.
  • You May Like: Volvo Xc90 Garage Door Opener

    Programming Multiple Genie Garage Door Openers To A Keypad

    This step assumes you have already changed the keypads default pin and have programmed at least one Genie garage door to the keypad. Then, follow these steps to program the other remotes.

  • Enter the keypad pin.
  • Press the Program key twice until the LED starts blinking slowly.
  • Enter either 2 or 3 as the number of garage door openers this keypad will service.
  • Press the Program key once to confirm the value.
  • The LED will flash twice and turn off.
  • Proceed to step 7 below to add the additional garage door opener to this keypad.
  • Put the next garage opener in programming mode by setting the button on the opener unit marked as Program,Learn, or Set.
  • Enter the access pin on the keypad.
  • Press the Up/Down key on the pad once.
  • Press the door number of the opener you are programming, for example, 2 or 3.
  • Now, press the Up/Down key about four times.
  • The garage door opener will start to function.
  • How Do I Clear The Memory On My Garage Door Opener

    Genie Garage Door Opener Reset Remote

    A garage door opener is a remote operated system used to open and close garage doors. It consists of a transmitter unit usually mounted on the wall and receiver unit mounted on the garage door. A radio frequency signal from the transmitter is sent to the receiver. The receiver sends a signal to the motor of the garage door to open or close. Garage door controllers are similar to garage door openers except that they allow you to remotely monitor and control the operation of your garage door from anywhere in the house.

    Recommended Reading: 6×7 Garage Door Lowe’s

    How To Program A Genie Garage Door Wall Console

    The wall console is a small device mounted on your wall or low in the floor. Here is how to program the Genie garage door wall console.

  • Press the program button. Hold it down until the LED light turns blue and then shuts off. The longer LED light should turn purple.
  • Next, press the door button on the console. Do it every two seconds until the garage door opens.
  • Related: How To Program A Liftmaster Garage Door Opener

    How To Adjust Force Settings

    Force settings are pre-programmed at the factory and applied during the open/closed limit settings steps. However, some conditions may require you to adjust the settings. Follow the steps below to adjust force settings.

    • Press and hold both UP and DOWN arrow buttons until the round LED turns red, then release the buttons. LEDs will show the current force level as shown in the force setting chart shown in your manual.
    • Press either the UP or DOWN arrow button until the desired UP force setting is shown.
    • Press and release the PRGM button to lock the desired UP force setting. LEDs will now show the current DOWN force setting.
    • Press either the UP or DOWN arrow button until the desired DOWN force setting is shown.
    • Press and release the PRGM button to lock the desired DOWN force setting. Both LEDs will turn blue then go out confirming the force settings have been changed and are locked.
    • The opener is now ready to operate and test.
    • Operate door from the wall console two full cycles then perform safety contact reverse test.

    Don’t Miss: Garage Door Opener Remote Replacement

    Where Is The Learn Button On Genie Garage Door Opener

    Whatever the model of your Genie garage door opener is, the learn button is usually located near the antenna of the main control box. You can also check this video for a more accurate find.

    The learn button is important in many troubleshooting and programming steps. It is imperative that you know where it is found.

    Programming Car2u To A Genie Garage Door Opener

    How to reprogram code (reset pin) on your Genie Intellicode garage door opener keypad.

    The Car2U device has a default factory setting, with button 1 being the Genie Openers. Follow the steps below to program Car2U to a Genie garage door opener.

  • Locate the Program or Learn button on the Genie opener
  • Press and hold the Program button. The long and round LEDs will turn blue, then release
  • The round blue LED should remain on
  • Press the Program button once more. The long purple LED will start blinking
  • Press the Intellicode button on the remote once
  • Both the long and round LEDs will start blinking purple
  • Press the Car2U button for one second and release
  • Both the long and round LEDs will turn from blinking to solid purple
  • Press the Car2U button once more for about one second, and release
  • Both the long and round LEDs will change to blue and turn off
  • Press the Car2U button again to test the Genie garage door opener function
  • Read Also: Replacement Genie Garage Door Opener

    How To Reset Linear Garage Door Opener

    If you need to reset your Linear Garage Door Opener either because it is no longer working normally or you may have lost the Remote, you can simply erase all memory from the garage door opener and then reprogram the remotes that are working along with the wireless keypad.

    If you want to reset your Linear Garage Door Opener, first, locate the Learn button on the garage door motor housing. It will usually be on the same side of the garage door opener unit as the antenna. It will usually have a small LED display next to it and is usually orange or green in color.

    Then, Press and Hold the Learn Button on the Linear Garage Door Opener until you see the LED Indicator Light in the display panel next to it turned off, which usually takes about six or seven seconds.

    ReadyToDIY is the owner of this article. This post was published on 2022-02-15.

    Finally, Press and Hold the Learn Button again until the LED Light goes off completely.

    Related Posts