Program Chamberlain Garage Door Opener

Share This Post

How To Program A Standard Liftmaster Remote Control

How to program a chamberlain garage door opener

A LiftMaster remote control can be programmed to activate many devices, including garage door openers, gate operators, commercial door openers, and external wired-in receivers. Heres how you program a standard garage door opener remote made by LiftMaster.

  • Locate the “Learn” button on your garage door opener. It’s on the same side as the antenna. You might have to remove the light lens to access it. The button may be either green, orange, red, purple, or yellow, and beside it is a small LED.
  • Press and release the Learn button.
  • Within 30 seconds of pressing the “Learn” button, press and hold the button you wish to program on the remote control for three seconds, then release.
  • The LED indicator light will turn off and/or the garage door operator lights will blink to indicate that programming was successful.
  • Its as easy as that!

    Ready Yourself Are You Sure You Want To Travel The Diy Path

    This task is dangerous. Before even touching your LiftMaster Chamberlain garage door opener, consider these vital factors:

    • Imprecise or incorrect level adjustments to door travel parameters will interrupt the safety reversal system.
    • If the garage door opener requires excess force to close the garage door due to inclement weather conditions or obstruction, the safety reversal system may be affected.
    • If the garage door opener model is old, NEVER force adjustments to compensate for a binding garage door.
    • Once reprogramming is complete, TEST the garage door opener safety reversal system.
    • Ensure the reprogrammed door height accounts for tall vehicles like trucks, vans, and SUVs to avoid damaging the car or garage door.

    PLEASE KEEP IN MIND: If the safety reversal system is damaged or rendered ineffective during the reprogramming process, SEVERE INJURIES or DEATH can occur. A closing garage door is under excessive tension, is a massive system, and is DANGEROUS. It can threaten the life of family, friends, children, and pets.

    Unless you are a handyperson with experience with this equipment, DO NOT risk it. Instead, look to a local certified LiftMaster Chamberlain specialist to install or fix it for you.

    Youre safe with a knowledgeable LiftMaster Chamberlain technician reprogramming that garage door opener instead.

    How To Reset Chamberlain Garage Door Opener In Seconds

    RobotPoweredHome is reader-supported. When you buy through links on my blog, I may earn an affiliate commission. As an Amazon Associate, I earn from qualifying purchases.

    Over the years, the garage doors have gotten heavier to enhance the garages security. So theres an increasing need for Garage door openers.

    I have been using the Chamberlain B4613T Garage door opener for several months now. Before that, I had the Chamberlain B2212T.

    I chose Chamberlain because they provide the best products at competitive prices and since I have been using their products for a while now I have pretty good knowledge about their workings.

    However, despite being a high-quality garage door opener, some issues do come up.

    My garage door opener somehow got connected to my neighbors remote control and it became a problem for both of us.

    Luckily, resetting the garage door opener was a quick fix to this issue.

    Nevertheless, it took me hours to find this solution. Hence, to help save you the effort, I have curated this article.

    To Reset Chamberlain Garage Door Opener in seconds you need to press and hold the LEARN button at the back of it. Once the memory is erased you can easily reprogram the remote control and keypad using the same button.

    Don’t Miss: Best Paint For Garage Door

    How To Program Your Liftmaster By Chamberlain Garage Door Opener

    Home Sweet Home! Its been a heck of day! You dearly miss those summer evenings when the sun set so late, and you had so much more energy! Now, when you finally get home, its pitch black and so cold outside! You press your garage door opener remotes button. And nothing happens. You try and try again. Until you finally admit somethings wrong. But not with your door opener remote. You checked it a while ago. Its even worse than that. You have to reprogram your LiftMaster or Chamberlain garage door opener!

    Psst! You could really relate to this story but what youve really, really liked about it is the picture of these 2 single garage doors? They are in the North Hatley LP Design, Moka Brown color, with 8-lite Orion windows.

    Or youve bought a brand new LiftMaster Chamberlain garage door opener and youve decided to install it yourself? Or maybe you had to replace the logic board of your LiftMaster Chamberlain garage door opener and you now must reprogram the travel? Here is the simplest and safest way to do it.

    Program Your Garage Door Remote Step By Step

    How To Program A Chamberlain Clicker Universal Garage Door Opener ...

    Here are a few simple steps for programming your garage door remote once you have access to all the components:

  • Make sure your new remote is the same brand as the garage door opener you are using. A remote meant for a LiftMaster opener will not communicate with a Genie opener, for example, because most openers and remotes operate on specific frequencies using different information.
  • Carefully climb up on the ladder so you can examine your garage door opener.
  • Inspect the opener to find the learn button. All modern garage door openers have one you have to look for it carefully if its not immediately apparent. If you still cant find the button, take off the light cover since the button could be hiding there.
  • Once you find the learn button, press it until it begins to blink. Once the light on the opener is flashing, press the open button on your garage door opener remote.
  • Generally, youll have a 30-second time limit between pressing the learn button and needing to press the button on the remote.
  • Give the process a minute, and then press the open button on the remote again to test the garage door. If it opens, youve successfully programmed your remote!
  • As there are many different types of garage door openers, the steps above are general guidelines rather than specific instructions.

    You May Like: How To Program Chamberlain Garage Door Openers

    Do You Think You Are Ready To Program A Chamberlain Garage Door Opener

    It is at this point that our guide on how to program a Chamberlain garage door opener comes to an end. However, now that youre more confident about this project, we hope youll be able to tackle it. Set up is very simple if you take your time at the beginning to identify the right steps. You wont need any expensive tools either.

    Wed love to hear about your Chamberlain garage door opener. Are you able to say that it was an easy process to program a Chamberlain garage door opener remote? Have you had to reprogram it? We would be delighted to see your opinions in the comments!

    Read More:

    Are You Up For The Job Dont Say We Didnt Warn You

    Before you start taking your LiftMaster Chamberlain down and opening it up, make sure youve taken this life-saving information to heart:

    • If you make adjustments that are faulty, or even just a bit off, the limits on the garage door travel system will interfere with how the safety reversal system functions.
    • Your garage door cant go up against too much force or it will create interference for the safety reversal system.
    • Old model openers shouldnt ever use force adjustments in place of binding a garage door.
    • After the reprogramming is complete, the first step is to TEST the safety reversal system on your garage door opener.
    • If you have a large vehicle that almost touches the roof of your garage, make sure it wont get damaged by the system. Check the clearance before bringing your vehicle into the garage.

    If you dont have a well-functioning safety reversal system, anyone who gets in its way could not only be seriously injured but possibly even killed by a garage door that closes on them. If you arent a skilled or experienced handy-person, do NOTunder any circumstancestake this on yourself. Contact a certified LiftMaster Chamberlain professional near you. These installers and technicians can do the work for you and give you peace of mind.

    Actual LiftMaster Chamberlain technician reprogramming an opening system.

    Read Also: 2 1 2 Car Garage Plans

    Decide How To Program Your Chamberlain Garage Door Opener

    Depending on the model of your door opener, you will need to follow different instructions. If youre lucky, you may find a video online for your model. The YouTube video below shows how to program either the 953EV or 956EV remote controls.

    However, if you dont see a video for your opener, dont worry! Some steps, such as finding the program button, may require assistance from the manual.

    Depending on your systems components, youll have different options. A door opener can be programmed to learn using its learn button. If you have a door control with a learn button, you can also use it. In addition to that, if you have a smart control panel, you can use it as well.

    If you want to start with and fix your garage door, you should make sure the door is closed and then check if there is a lightbulb on the opener. In the absence of one, install one. When the programming is complete, the lightbulb will flash.

    Programming A Remote Control With The Door Control

    How To Program Your Chamberlain Garage Door Opener. Super Easy!
  • 1Press the “Learn” button on your door control, if it has one. Not all door controls will have learn functions, but yours may. If your door control has a plastic cover thats able to be lifted off, it may be located right underneath it. Press this button once to access the door controls pairing mode.XResearch source
  • If your door control looks more like a doorbell, you may be able to access the “Learn” function by holding the light button on the side of the device while pressing and releasing the front button.XResearch source
  • If you have a smart door control, you can activate pairing mode through its menu. Navigate to the program tab of the menu, then select “remote.”XResearch source
  • 2Push a programmable button on your remote control. Select and press one of the face buttons on your remote controlit doesnt matter which one. The garage lights will flash, or you might hear 2 clicks. This tells you that youve successfully programmed your remote control.XResearch source
  • Some types of remote controls, like the Chamberlain Universal Remote, may need to be put into pairing mode before they can be programmed. If you press the bottom button for 15 seconds, then release it, the remote will be in pairing mode for 60 seconds.XResearch source
  • Read Also: Garage Door Lock Kit With Bars

    How Do I Add Or Reprogram A Hand

    Press and release the LEARN button on the garage door opener unit. The learn indicator light will glow steadily for 30 seconds. Within this 30 second time period, press and hold the button on the hand-held remote. Next, release the button when the overhead opener units lights blink. If light bulbs are not installed on your opener, then two clicks will be heard.

    To erase all codes from motor unit memory:Press and hold the LEARN button on motor unit until the learn indicator light goes out . All previous codes are now erased. Reprogram each remote or keyless entry you wish to use. Press and hold the ENTER button. Next, release the button when the overhead opener units lights blink. If light bulbs are not installed on your opener, then two clicks will be heard.

    Tips To Program A Chamberlain Garage Door Opener Remote

    The programming for your Chamberlain garage door opener remote may need to be erased in the future if you find that you cannot use it anymore. Moreover, if you lose your remote control, you will have to add a new one to your system.

    It is not enough to unplug your door opener for a long period of time to accomplish this. Additionally, if youre going on vacation, you can unplug your door opener. There will be no need to reprogram it when you return.

    Press the learn button on your Chamberlain garage door opener remote control in order to erase an existing program. You can also use a control panel with a learn button.

    If the LED does not go out after a few seconds of holding the learn button, please hold it for a few more seconds. Approximately six seconds will pass. The codes that were programmed into the door opener will now be erased. It is possible to program the new ones by repeating the steps above in order to program them.

    Don’t Miss: How To Change Code On Garage Keypad

    Models 375lm 375ut And 380ut Programming Instructions For Dip


    Genie Garage Door Opener Keypads

    Program Chamberlain Myq Garage Door Opener To Car

    Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK

    Step-By-Step Programming Procedure

  • Reset Keypadslide keypad cover halfway up. While pressing the # and 8 buttons simultaneously, slide the Keypad Cover the rest of the way up until it latches. Release # and 8 buttons. At this point, if the backlit keypad light stays on, proceed directly to step 2. If the backlit keypad light goes out, close the cover pad and reopen it until it clicks. Proceed to step 2.
  • Press 3, 5, 7, and # buttons in said order.
  • Enter your PIN and press the # button. Your PIN number can be created from any group of numbers up to 8 digits of your choice. Note: Do NOT use the# or star key.
  • Enter Door Code, as determined from the chart at left, and press the star key.
  • Slide Keypad Cover down.
  • Test Keypad by sliding the cover-up until it latches. Enter your PIN and press the star key. Your door should operate.
  • This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters . The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers.

    Switch Settings

    You May Like: Dip Switch Garage Door Opener

    Check That Your Remote Control Is Compatible With Your Door Opener

    Its important to remember that Chamberlain remote controls will work only with garage door openers made after 1993. And your garage door will also need photoelectric sensors.

    If youre not sure whether your door has those sensors, take a look at your door tracks. If theyre there, theyll be positioned at or near the bottom of the tracks. If your door opener uses a dip switch instead, a Chamberlain remote control wont work.

    Now check that your model of door opener will work with your remote control. To do this, you need to know the color of the learn button inside your door opener.

    Mount your ladder and remove the cover from the opener. The learn button is inside, usually on either the back or side panel, near where the antenna hangs down.

    Different models of openers will have learn buttons in different colors. Your remote control manual should tell you what color button is compatible. If youre still not sure, visit and check out the compatibility chart.

    If your remote control is compatible with your garage door opener, youre ready to move to step 2.

    Pro tip: You may be able to save yourself a trip up the ladder by looking for the wire antenna. This hangs down from the side of your door opener. If its yellow or purple, the learn button will be the same color. If the antenna is a different color, though, youll need to get out that ladder.

    Instead Of Programming Your Worn

    Sounds way too dramatic? Does it leave you feeling we want you to buy something you dont need by instilling fear in you? Well, think again!

    Here are 2 important innovations in LiftMaster and Chamberlain garage door opener technology, one in 1993 and the other in 2012, you should know about.

    Your LiftMaster or Chamberlain garage door opener was manufactured before 1993? Whoops! You should NOT reprogram it. You must replace your garage door opener because it is a really big safety hazard for your family. Its a fact.

    Since 1993, garage door openers made in the US and Canada have had to include 2 reversal systems designed to protect you and your loved ones.

    Before that, it really was the Far West. Everybody was on their own. There was no requirement for manufacturers to prevent garage doors from closing on objects like your kids!!! Kids are kids. You cant expect them to remember everything when theyre busy playing. Besides, why would they have to think about these things when simple innovations could protect their lives, right?

    Also Check: Metal Garage With Living Quarters

    Program The Opener In 12 Steps

  • Confirm that the garage is closed but still plugged in. Also, check that the trolley is near the garage door.
  • Find your garage door opener adjustment buttons.
  • Press and hold the black square button. One of two things will happen either the up button will flash, or a small beep will sound. This is alerting you that you can set your opener in the OPEN POSITION going forward.
  • Press and hold both ARROWS simultaneously and watch as your garage door opens. Once its fully open, stop and look this is the UP position you want your garage door to be in.
  • Press the black square button . When you do this, youll notice that the light on the opener will flash twice. Then, the DOWN arrow will flash. This is to inform you that youve LOCKED your OPEN POSITION. Now you have to teach the opener what the CLOSE POSITION is.
  • Go back to the DOWN arrow. This time, press and hold the button until the garage closes !
  • Press the black square button. This will teach the opener that this is the CLOSED POSITION that you want. The opener lights will flash twice, followed by the UP arrow flashing. This means that the opener has LOCKED the DOWN POSITION. Youre now ready to set the mode for force programming.
  • Press the UP Arrow. When the door travels to the programmed UP position, the DOWN Arrow will begin to flash.
  • Press the DOWN Arrow. The door will travel to the programmed DOWN position. Programming is now complete.


  • Close your garage door.
  • Related Posts