Liftmaster

Liftmaster Garage Door Opener Keypad Programming

Aaron T
By Aaron T

Share This Post

Lm Liftmaster Keyless Entry Program Instructions

How to Program LiftMaster’s 877LM Wireless Keypad to a Garage Door Opener
  • Security+® 315MHz rolling code technology assures a new code is sent every time the keypad is used
  • Temporary password option enables friends or service people to enter the garage without giving them your personal code
  • Completely wireless powered by one 9-volt battery
  • Weatherproof flip-up protective cover
  • Backlit keypad makes numbers easy to see, even in the dark
  • One-button-to-close feature makes it easier than ever to close your garage door
  • Programs in 2 easy steps

The MHz frequency of your garage door opener will determine what keyless entry system will work with your system. See below to find out if the 377LM Keyless Entry is compatible with your opener.

  • Your garage door opener motorhead has a purple learn button, or
  • Your garage door opener motorhead has a purple antenna, or
  • Your original remote has silver buttons with glowing blue lights
  • Compatible Liftmaster garage door opener models: 1345, 1355, 1356, 3220, 3255, 3240, 3265, 3270, 3280, 3800, 3500, 3850, 3585, 3595
  • Compatible Raynor garage door opener models: Pilot 3265RGD, Navigator 3245RGD, Aviator 3280RGD and Commander II 3240RGD manufactured 2006 to 2013

The 377LM Keyless Entry has been discontinued. Use the 877MAX Keyless Entry as a replacement.

Why Do I Need To Keep My Pin Private

If you do not keep your PIN private, then you will be giving out access to your garage. That means that people could break into your home without actually breaking in. It makes for a hazardous situation. Think about the pin number for your bank. Anyone with the pin number to your ATM card can withdraw money. Would you want to give that out to everyone else?

How To Program Liftmaster Garage Door Opener

LiftMaster has been making industry-leading garage door openers for over 50 years. That means there are a lot of different models on the market, so figuring out to program them may be a challenge.

In this article, well walk you through how to program your LiftMaster garage door opener step-by-step.

Things you will need:

Read Also: How To Organize Tools In Garage

After You Program Your Device

After you program your LiftMaster garage door opener, we recommend that you test the auto-reverse function of your LiftMaster garage door opener.

This feature is crucial to the safe operation of your device.

If the auto-reverse function fails, it could lead to accidents and life-threatening injuries. Therefore, if you notice any problem with this function, power the device off immediately until resolved.

How To Program A Liftmaster And Genie Garage Door Opener Remote Control

How To Program Liftmaster Keypad Garage Door Opener

LiftMaster and Genie are two of the most trusted brands in the garage door opener business. Both companies provide easy-to-use and dependable remote controls when you purchase one of their state-of-the-art openers. Creative Door Services is proud to carry these openers, and we recommend them wholeheartedly. Here are step-by-step instructions for programming the remote controls that come with these opener brands.

Don’t Miss: How To Insulate Garage Doors

How Much Does A Liftmaster Garage Door Opener Cost

The average cost of installing a garage door opener greatly varies. The cost of a LiftMaster garage door opener with installation is $150-$400. However, you can always install this yourself to save some money. However, you need to ensure that you are confident and comfortable doing the job so that you dont make any mistakes.

What Are The 3 Buttons On A Liftmaster Garage Door Opener

The three buttons on a LiftMaster garage door opener are the Learn button, the Smart/Program button, and the Pin button. The Learn button is used to program your remote. The Smart/Program button is used to pair your remote with your keypad. The Pin button is used to reset the pin on your keypad.

Liftmaster Keypad Programming: How to Easily Program Your Remote

Also Check: 100 Miles Of Garage Sales

Homelink Garage Door Opener Programming

HOMELINK IN-CAR REMOTE PROGRAMMING INSTRUCTIONS

To program a built-in-car transmitter to a rolling code garage door opener , you should take the following steps.

  • Clear out anything previously programmed into the in-car system from the factory by holding down on the 2-outside buttons simultaneously, until the in-car LED starts flashing rapidly. This may take up to a minute .
  • Go to the Learn Button on your garage door opener. The button is usually next to the area where the floppy antenna is connected to the motorhead. With Genie, it is most often behind the light lens, and an indicator light flashes red when pressed. With Sears or Liftmaster it is near, or part of, the terminal screw board, and is a red, green, or purple square button with a green, amber or purple indicator light. Press this learn button momentarily. The indicator light will turn on and blink if Genie or otherwise stay lit. For Genie systems, go back to the in-car transmitter button you programmed and press this button 3 or 4 times, or until the door starts moving. This should set your in-car transmitter to your garage door opener. For Liftmaster, Sears, or Linear Megacode press and hold the in-car button you programmed until the garage opener light flashes. Your in-car is now programmed to operate your door.

    • Programming a Fixed-Code Device

    These devices have internal dip-switches located near the battery of your remote.

  • Test the in-car remote by pressing the button you chose to operate your door.

    • Genie Garage Door Opener Wireless Keypad Model Gpwk

    How to Program LiftMaster’s 877MAX Wireless Keypad to a Garage Door Opener

    This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters . The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers.

    Switch Settings
    0

    Door Code in Step 4: ___ ___ ___ ___

    To make a copy, highlight area and copy into your word program. You can then print out a legible copy of the chart and the programming instructions from your word software.

    Step-By-Step Programming Procedure

  • Reset Keypadslide keypad cover half way up. While pressing the # and 8 buttons simultaneously, slide the Keypad Cover the rest of the way up until it latches. Release # and 8 buttons. At this point, if the back lit keypad light stays on, proceed directly to step 2. If the back lit keypad light goes out, close the cover pad and reopen it until it clicks. Proceed to step 2.
  • Press 3, 5, 7 and # buttons in said order.
  • Enter your PIN and press the # button. Your PIN number can be created from any group of numbers up to 8 digits of your choice. Note: Do NOT use# or star key.
  • Enter Door Code, as determined from the chart above, and press the star key.

    • Recommended Reading: Garage Door Screens Roll Up

    Programing A Liftmaster 3 Button Gate Remote

    If you have also purchased a LiftMastet gate remote, then you may want to know how to program that as well. There are a few steps you can take in order to complete this.

  • Select Learn. Press and release the learn button quickly.
  • Hold the button. Now you will have 30 seconds to hold down the button that you wish to program. This needs to be done on your remote.
  • Release the button. Release the chosen button once the motor unit light blinks. It may also produce two clicks are heard.
  • Test it all. Test the button by pressing it.

    • How To Do Liftmaster Keypad Programming No Enter Button

    Garage Storage Lab is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

    To keep our garage space safe from intruders, we often use various automatic or controlled door openers like LiftMaster 877Max or LiftMaster 877LM. These garage door openers only allow people who have a passcode. However, sometimes your kids or the sitter need to enter the garage while you are away or your UPS guy might need to leave an expensive package for you but you are not home to let him in. In these circumstances, knowing how to do LiftMaster keypad programming no enter button will come into play.

    This blog is for you if you dont know how to use the LiftMaster keypad without the enter button.

  • Helpful Products For Your Garage

    • Also Check: Garage Door Cable Repair Cost

    What Do I Do If My Liftmaster Remote Stops Working

    If your Liftmaster remote stops working, you will need to reprogram it. To do this, press and hold the Learn button on your keypad for approximately six seconds. Then, press and hold the Smart/Program button on your remote for six seconds. This will pair your Liftmaster keypad and remote. You can also consult a professional for more tips.

    Contact Us To Learn More About Liftmaster Garage Door Opener Programming

    Programming Liftmaster 387LM Universal Wireless Keypad

    If your garage door opener isnt working or youre experiencing difficulties programming your remote to a LiftMaster garage door opener, Quality Overhead Door can help. Contact us today for assistance. You can count on our technicians to remedy the issue as soon as possible.

    If youd like to install a new garage door opener, reach out to request a free estimate. You can also view our LiftMaster garage door openers online or call us at 419-578-8700 to learn more.

    Don’t Miss: Roll Up Garage Door Installation

    How Do You Program Liftmaster Wall Controls

    To program LiftMaster wall controls, press and hold the Learn button for approximately six seconds. This will put your wall control into pairing mode. Then, press and hold the Smart/Program button on your remote for six seconds. This will pair your remote with your wall control. You can now use your remote to operate your garage door.

    Switch The Mode From Operate To Program

    At first, youll have to remove the faceplate from the door opener. After removing the faceplate from the door opener, search for the dual operation or program. When you find the dual operation or program, youll see that its set on the operating mode. Youll have to switch the mode from operating to program mode. By switching the mode, youll be able to change the pin of your garage door opener.

    Read Also: Liftmaster Wall Mount Garage Door Opener

    New Video: How To Program Your Garage Door Remote & Keypad

    How to program your garage door remote and keypad .

    To program your remote:1. Press & release the learn or smart button on the back of your garage door opener. The learn indicator light will glow steadily for 30 seconds.2. WITHIN 30 seconds, press & hold the button on your hand-held remote.3. Release the button when the motor unit light blinks. It has learned the code. If the light bulbs are not installed 2 clicks will be heard.

    To program your keypad:1. Press & release the learn button on your garage door opener. The learn indicator light will glow steadily for 30 seconds.2. WITHIN 30 seconds, enter a four digit code of your choice on the keyless entry. Then press & hold the ENTER button.3. Release the button when the garage door opener lights blink. If no light bulbs are installed 2 clicks will be heard. Your code has been accepted.

    DISCLAIMERMount Garage Doors Inc accepts no liability for the content of these pages, or for the consequences of any actions taken on the basis of the information provided.If in doubt, please call 549-2668 or 1-877-683-6677

    How To Program A Liftmaster Max Remote Control

    How To Program Your Liftmaster Garage Door Opener Remote and Keypad.

    LiftMaster MAX remotes work with all 315 MHz or 390 MHz LiftMaster garage door openers manufactured since January 1993 . Follow these steps to program the various MAX models.

  • Locate the “Program” button on your garage door opener or keypad. On the 890MAX and 895MAX remotes, locate the “Program” button and press it using a safety pin or paper clip until the LED on the front of the remote control turns on. It will then be ready to program. On the 893MAX remote, locate the “Program” button on the back of the device located under the visor clip. Press the button to activate it. On the 877MAX keyless entry keypad, press the * and # buttons simultaneously until the lighted keys stop flashing and remain on steady. Note that when the controller is in programming mode, you need to program one button at a time.
  • Press and release the button on the remote control that you wish to program.
  • Wait for the remote control LED to stop blinking, then slowly press and release the button again. Repeat until the light bulb blinks. Dont press the button after the light bulb blinks as this will prompt the remote to transition into a different setting, rendering it inoperable. If you do press the button, you will need to go through the steps again from the beginning.
  • Once the light bulb blinks, press any other button on the remote control.

    • To program other buttons on the remote control, repeat steps one to four.

    You May Like: Home Depot Garage Door Replacement

    S To Program Your Liftmaster Overhead Door Opener Remote

    To program your LiftMaster garage door opener keypad, follow these six easy steps:

  • Locate the learn button on your LiftMaster opener. If you have a wall control, use this button instead.
  • Press and release the learn button. If your LiftMaster opener has a MyQ Control Panel, press and release the button twice.
  • Press and hold the button on your remote within 30 seconds of completing the previous step. Hold it down for three seconds.
  • Depending on your model, the opener lights will blink or the LED lights will go out to indicate that the programming has been successful.
  • To ensure the programmed button functions properly, press it down. Repeat the steps if you find its not functioning correctly.
  • Repeat the process for other remotes or buttons if need be.

    • Universal Home Remote For Homelink

    Programming a Rolling Code Garage Door Opener

    If your in-car remote has 3 LED lights, one above each button, you should follow the instructions below to program your Rolling Code Garage Door Opener.

  • Press the outer two in-car buttons simultaneously and release .
  • Place the garage door opener into learn mode by pressing the small square colored button, or the small round black button on a Genie, located behind the light bulb globe in the garage. This may require the use of a ladder, follow all safety precautions.
  • The LED on the garage door opener will go on immediately. For Genie openers, the LED will begin blinking.
  • Press and hold the button on the in-car remote that you want to use for the operation of the garage door to activate.
  • Watch for the garage door to activate.
  • When the garage door activates, release the button and depress again the selected button to lock in the program.
  • Programming of Rolling Code garage door opener is now complete.

    • Programming a Fixed Code Device

    Below is a picture of a typical 12-switch DIP switch layout located on your hand-held remote control under the battery cover . Note: Genie, Linear, Multi-Code and Stanley have only 2 position switches: up or down.

  • Press all three in-car buttons simultaneously and release .
  • When you are done entering all the DIP switch settings, press all three in-car buttons simultaneously and release them.
  • Press and hold the button that you want to use for operation. Watch for the garage door to activate.

    • Recommended Reading: Golf Club Rack For Garage

    Programming Instructions For Genie Remotes:

    Programming Genie Intellicode Remote Transmitters

  • Press the Receiver Learn Code button on the powerhead receiver of your door operator. This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6-inch antenna wire that protrudes from the motorhead. When pressed, a radio signal indicator light will start blinking red for 30 seconds. **
  • After pressing the Learn Code Button once, press your transmitter button three times for your system to grab the frequency and code it in.
  • Press the transmitter button once more to test the system and start your door moving.

    • ** To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2.

    Programming The 877max Keyless Entry

    How To Program A Liftmaster Garage Door Opener Keypad
  • Press and hold the star and the # keys until the lights on the keypad stop blinking.
  • Enter a four digit PIN of your choice and press the # button
  • Press the Enter button the number of times shown in Chart B below, based on your garage door opener type.
  • To exit programming, press and release the 0 button.
  • Press and release the Learn Button on the garage door opener motor head in the garage.
  • Enter the 4 digit PIN programmed in step 2 and hold down on the Enter button until the lights flash or 2 clicks are hear, approx 4 seconds. Test keypad.
    • Chart B

    Recommended Reading: How To Program Car Garage Door Opener

    Liftmaster 387lm And 387lmc

    For these remotes, you first need to find out which type of garage door opener you have and follow the instructions for your type:

    • Type 1: Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, or Do It opener with three-position DIP switches.
  • Determine your opener ID: ID 11 has 9 switches and is from the US, ID 12 has 9 switches and is from Canada, ID 15 has 8 switches, and ID 19 has 7 switches.
  • Write down the DIP switch sequence: each switch will be in the + position , the 0 position , or the position .
  • On your keypad, press and hold the * and # buttons until the lights stop flashing.
  • Enter a four-digit PIN of your choosing, then press #.
  • Enter your ID number from above, then press #.
  • Enter your DIP switch sequence from above, then press #. Your programming is now complete.
    • Type 2: Genie, Linear, or Moore-o-Matic openers with two-position DIP switches.
  • Determine your opener ID: ID 13 is a Genie opener with 12 switches, ID 14 is a Linear opener with 10 switches, ID 16 is a Stanley opener with 10 switches, ID 17 is a Genie opener with 9 switches, ID 18 is a Linear or Moore-o-Matic opener with 8 switches.
  • Record your DIP switch sequence: use a 1 for each switch that is up and a 2 for each switch that is down.
  • On your keypad, press and hold the * and # buttons until the lights stop flashing.
  • Enter a four-digit PIN of your choosing, then press #.
  • Enter your ID number from above, then press #.
  • Enter a four-digit PIN of your choosing, then press #.
  • Enter 11, then #.

    • Related Posts

    Previous articleLinear Garage Door Opener Programming
    Next articleGarage Door Remote Openers Replacements

    Categories:

    Hot right now:

    Garage Ceiling Fan With Light

    Editor Picks Aaron T - 0
    Pros Of A Ceiling Fan In The Garage Updated Garage Ceiling...

    Screen Door For Garage Door

    Door Aaron T - 0
    Keep The Pests Out And Add Another Room To Your Home ...

    Garage Door Repair Dallas Ga

    Readers Choice Aaron T - 0
    Rely On Us For Expert Garage Door Repair In Dallas Ga ...

    Company:

    Follow on:

    © 2022 GarageAdvice.net | Contact us: contact@garageadvice.net