How To Fix Garage Door Opener

Share This Post

Solution : Replace The Safety Sensors

How to Fix a Garage Door Opener

You might have to replace a single or pair of the sensors because they might be defective if youve checked that nothing is obstructing the safety sensors and that they are clean, but the light indicators are still off.

Also, one or both of the sensors might be faulty if the red LED on the transmitter is off while the red indicator of the receiver sensor is on. Similarly, one or both of the sensors are defective if the red LED light on the transmitter is on while the red indicator light of the receiver is off.

Contact RYOBIs customer service or anyone of their authorized service centers to come to replace your sensors. You can also buy and replace the sensors if you have some experience in replacing safety sensors.

Tighten The Loose Components

Opening and closing the garage door every day will cause some bolts and nuts to become loose. If thats the cause of the noise youre hearing, then you are in luck. All you have to do is tighten the bolts or nuts and the noise should disappear.

While youre at it, take time to check that all nuts are tightened. If you need to replace the screws or nuts, do so to avoid disturbing sounds.

Symptom: The Door Goes Up But It Only Goes Down When You Hold Down The Wall Switch

Fix: Align or replace the safety sensor

If the door goes up but goes down only when you hold down the wall switch, check to see that the safety sensors are in alignment. The small light on each sensor should be lit up when nothing is between them. Door sensors do go bad, so if no light is showing at all, you may need to replace them. You can save yourself some time by using the existing wires. Also, direct sunlight shining on sensor eyes can make them misbehave.

Read Also: I Lost My Garage Door Opener

Basic Maintenance And Quick Fixes

If your garage door is behaving well at this moment, you can probably keep it working that way almost indefinitely if you follow a simple inspection and maintenance routine. These same tips may also correct problems that are just beginning to appear:

If none of these solutions fix your problems, or if you would rather just let someone else fuss with the door, look into calling a good garage door installer and repair technician.

Here are some other common garage door problems you may be able to fix yourself.

Common Garage Door Opener Issues And How To Fix Them

How to Repair a Garage Door Opener

Garage door openers are prone to have various issues depending on the maintenance of the opener or its quality. Those issues can become a nuisance in your daily schedule since having trouble opening or closing your door can make you lose a lot of time.

Some of the most common garage door opener problem can be easily solved by DIY repairs. However, if the problem is complicated, the better solution will be contacting a professional garage door repair company such as Naperville Garage Door Repair.

What Are the Most Common Garage Door Opener Issues?

Recommended Reading: Ford’s Garage Menu Fort Myers

Best Garage Door Opener Brands

Raynor Garage Doors

With decades of experience installing, repairing, and serving garage doors and openers, hands down, the best brands in the business are Raynor and LiftMaster.

Raynor has been around for 75+ years. When it comes to the best in design, engineering, and production experience, they are the #1 choice for most garage door repair professionals.


LiftMaster helps homeowners busiest entryways smarter, safer, and most certainly secure. LiftMaster garage door openers come in many types:

LiftMaster also offers the Amazon Key App so you can start getting Amazon Prime packages securely and conveniently delivered inside your garage.

Solution : Repair Or Replace Your Garage Door Springs

Inspect the door spring assembly, torsion, and extension spring for any damage. Disconnect the garage door opener from power if you see any damage or considerable wear to the door spring.

Contact a qualified service technician to look at them if youre unsure so they can fix or install new ones. Although not advised, it is possible to replace the springs yourself by putting the door in the position that loosens the tension on the springs, usually the open position, allowing you to work with the springs safely.

You should check your products warranty before venturing to fix anything yourself. Ensure that youre familiar with all the risks and take every safety precaution advised in the user manual because heavy machinery like this can lead to severe injuries or death.

Don’t Miss: Cost To Build Detached Garage With Apartment

Why Does My Garage Door Go Back Up

The photo eye sensors we talked about in #1 can also make your garage door stop and go back up partway through closing. Why? The photo eye sensors are designed to sense objects and people in the path of the door and stop the door from closing on them. When they stop the door from continuing its downward path, they automatically send it back up. This is a valuable safety feature and also easy to correct.

If your door is only closing part of the way and then going back up, there may be something in the path of the door. In some cases, it may be obvious, such as a bike or other outdoor equipment. But, photo eye sensors are designed to be sensitive to all sorts of objects, which means that sometimes the offending object might not be so obvious. Depending on your sensors, they can also become obstructed by mud, leaves and other yard debris. Or, if there is dirt built up on the lenses, they may interpret the dirt as an object in the doors path.

Clear all leaves, mud and other yard debris away from the threshold of your garage door. Clean the lenses as well.

If youre sure that theres nothing blocking your sensors, then inspect the doors track. Sometimes, there can be buildup on the track that prevents the door from operating properly. You can clear buildup with a damp rag. Its also a good idea to periodically wipe down your garage doors track to prevent this issue from happening in the first place.

Does My Garage Door Need Repairs

Garage Door Opener Troubleshooting and Repair – How to fix common problems

If your door is stuck in the open or closed position without a clear explanation, such as a need for new batteries in your remote transmitter or an object blocking the doors photo eye sensors, then yes, it needs to be repaired.

Other clues that your door requires repairs include:

  • Damage to the door itself, such as warping or cracks that interfere with its ability to move up and down.

If you suspect any of these problems, dont try to repair the problem yourself. Although the thrill of DIY can be tempting, at-home garage door repair is a dangerous undertaking. Even with the best of intentions, you could accidentally injure yourself or someone else because you arent prepared for any and all scenarios. Resist the urge to handle the problem yourself. Call a trustworthy garage door repair company and allow them to properly diagnose and correct the problem.

Also Check: Lowe’s Garage Door Springs

Extend The Life Of Your Garage Door

First and foremost, most professionals will offer product and labor warranties/guarantees. And those alone can extend the life of your garage door.

But beyond that, a professional can also prevent problems from occurring.

Though a garage door may seem simple on the surface, its actually a more complex piece of machinery than most people know.

There are lots of moving parts involved. And knowing how small problems can affect the machinery at large takes lots of training and experience.

With a garage door opener repair professional, you can leverage the benefit of that training and experience.

Sure, these technicians will be able to repair the problem for maximum effectiveness later. But beyond that, theyll also be equipped to spot serious problems early on.

For instance, an unbalanced garage door can be hard to spot for the typical homeowner. But it could be putting serious strain on your opener over time. And that can lead to big problems later.

With a professional, you can fix those problems before they require a heavy investment.

Lubricate The Garage Door

If the garage door is not maintained properly, it will not be able to open properly. Liftmaster professional garage door opener service providers are experts in this maintenance works. Lubrication is an important part of maintenance. If you do not do this, the moving parts may get clogged, causing the opener to stop working. Make sure that you properly lubricate all the mobile parts and then try again.

Also Check: Carports In Front Of Garage

Open The Door To The Best Equipment

Raynor Ultra II with WiFi Garage Door Opener

Finally, working with a garage door opener repair professional gives you access to better equipment and brands than youd have access to on your own.

To explain, big box stores like Home Depot and Lowes may offer a few different garage door opener models. And they may even have a few repair parts available too.

But professional repair services have loads more options available to them, both in terms of parts and different brands.

That means when you work with a garage door opener repair professional, youre opening up the door to better equipment and parts that you otherwise wouldnt have access to.

Added to that, many repair professionals are able to purchase equipment from vendors at a discounted rate.

So not only are you getting the best brands and models in the industryyoure also getting them at a cheaper rate.

Its a win-win!

Check Garage Door Opener Mechanism

Garage Door Opener Repair &  Installation
  • If the garage door opener is receiving power but still not operating properly, it could have a mechanical failure.
  • If the door wont open but the engine sounds like it’s running, the main gear drive may have broken and need replacement.
  • If the trolley carriage moves but the garage door doesn’t, one of the components of the carriage is broken and needs replacement.
  • If nothing happens at all, the circuit board of the garage door opener motor likely needs replacement.
  • If you have a chain drive garage door opener, make sure that the chain has the correct tension: too little tension can cause the chain to slip the sprocket and fail to pull the trolley.

Recommended Reading: How To Open Garage Door Manually From Outside

Benefits Of Professional Garage Door Opener Repair Service

Your garage door opener may see a wide range of problems throughout its life. Faulty photo eyes, electrical problems, burnt-out motors, snapped springsall can strike and leave you stuck .

And though you might be tempted to tackle your garage door opener repair on your own, this job is often best left to the professionals.

This guide takes a look at the top five reasons to consider professional garage door opener repair overdoing it DIY instead.

Ryobi Garage Door Opener Wont Close

Amongst the array of possible issues that your garage door opener can present you with, its refusal to close can endanger the security of your home.

The safety sensors are usually the prime culprit when RYOBIs garage door opener gets stuck fully open and wont respond to being closed with your smartphone, keypads, and even your car remote.

Several reasons could lead to malfunctioning safety sensors. Youll find it helpful to know how to run diagnostics for every nerve-rearing eventuality.

Read Also: How To Sync Garage Door Opener

Diy Garage Door Opener Repair Vs Hiring A Professional

Things like dental concerns, surgery, and car repair are better left to the hands of professionals. However, how about garage door opener repairs? Can you do them by yourself or should you hire a technician?

Well, remember that using a DIY kit and conducting the repairs on your own can be risky. Every year, the U.S. Consumer Product Safety Commission warns the public about the injuries and deaths that garage doors can cause. So, before you decide, let us discuss the drawbacks of performing a garage door opener repair on your own.

You Notice Visible Vibrations When The Opener Operates

How to fix a garage door opener Board Repair – Remote not working

When you glance up at your garage door opener in use, can you see it moving in place?

The shaking could mean that the opener is loosening from its hold on the ceiling. Leaving this go could cause the opener system to fall. Why risk yours falling on the garage floor or, worse, on top of a vehicle?

On the other hand, shaking could mean the motor is being overworked. The shaking could cause the unit to drop the garage door, creating major damage to the door.

You May Like: Replace Spring On Garage Door

Garage Door Won’t Respond To Remote Or Keypad

The Spruce / Ana Cadena

There are several possible solutions when a wireless remote control or mounted keypad stops operating the opener:

  • Move closer to the door. It’s possible you are out of range of the antenna inside the garage. Modern garage door openers are essentially small radios that operate at about 315mH, and a few feet of extra distance can affect the signal.
  • Make sure that the antenna on the motor unit is hanging downward and is not damaged in any way.
  • If the door functions fine with the hardwired wall switch, it’s likely the battery needsreplacingin the remote control or keypad.
  • Reprogram the remote control or keypad. The sensitive electronics in the remote control or keypad can sometimes lose its programming and may need to be reset. Each garage door opener has a slightly different method of reprogramming, so consult the instructions or look online for information on how this is done for your particular opener.
  • Do Some Initial Checks

    If the door wont open, then you need to do some quick checks first of all. It may be something very simple thats stopping the door from opening, and so youll be able to solve the problem quickly. Check the following on your garage door opener:

    • Is the garage door opener plugged in, and is the circuit breaker in the right place?
    • Has the door been locked manually?
    • Have the batteries of your remote control worn out?
    • Are you in the correct range to open the garage door?

    If you still need to get into the garage quickly, you can open the door by pulling the release cord. This disconnects the trolley, so you can open the door manually. Never do this when the door is open though, as it can cause it to come crashing down.

    Also Check: Garage Door Openers At Menards

    Symptom: Everything Works Fine Except The Lights

    Fix: Replace the light socket

    If the bulbs are OK but don’t light up, you probably have a bad light socket. To replace the socket, you’ll need to remove the circuit board to get at it. Use the same steps as in ‘Replace the Circuit Board’ to accomplish this.

    Once the circuit board is removed, pop out the old socket by depressing the clip that holds it in place. Remove the two wire connections and install the new socket. Replacement sockets cost less than $15.

    Be sure to use a bulb of the correct wattage. Using lightbulbs with a higher wattage than the socket is rated for will cause a socket to fail. Not only is this bad for the socket, but it can also be a fire hazard. If your light cover has turned yellow from heat, you’re probably using too strong a bulb.

    The Transmitter Batteries Are Dead

    How to Repair a Garage Door Opener

    This may sound obvious, but your garage door transmitters need power to work. If the batteries in your transmitter are dead, the transmitter wont be able to send a signal to your garage door to open.

    First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.

    Changing the battery on your garage door transmitter is pretty simple. On most, you can simply slide the door open on the back of the transmitter and remove the battery. Others may be screwed in to keep the battery more secure, so this type of transmitter will require a screwdriver to open.

    After removing the old batteries, make sure the plus and minus signs line up with the plus and minus signs on the inside of the transmitter. Otherwise, the new battery wont work in the transmitter, and it could give you a false sign that something else may be wrong. Once the battery is in place, test the transmitter, and if it works, replace the transmitter door.

    Also Check: Garage Door Repair Hampton Va

    Do Garage Door Openers Have Fuses

    A garage door opener is a combination of various features that allow the product to function properly. Depending on the model or brand you own, it might include a fuse on its list of parts. This component is an essential part of inspecting if your garage door opener is malfunctioning.

    A fuse is an essential part of an electrical circuit. To put it simply, this safety feature is what protects your garage opener if theres something faulty within the circuit. The fuse has a small wire inside that will melt and break the circuit if theres too much electric current passing through.

    There are a few ways to tell if a fuse in your garage opener has burned out:

    • Your circuit breaker is on.
    • Your garage opener has no power, but the system is plugged into an outlet.
    • You know the outlet the system is plugged into has power.

    Either the fuses or another internal component is likely the cause of your faulty garage opener. Its best to consult a professional technician if you suspect an issue is occurring with your garage opener. This way, you wont encounter any safety issues. If the fuse is your concern, the technician will check to see if its still operating by:

    • Locating the glass fuse
    • Inspecting if the fuse has blown
    • Using proper tools to check its performance
    • Replacing the fuse if needed

    Related Posts