Go Control Garage Door Opener

All Orders Over $100 In The 48 Continental United States Receive Free Ground Shipping

Orders checked out with Standard Shipping typically take between 1-2 business days to be processed and shipped. Expedited orders placed before 2:00 p.m. PST will be shipped the same day. Weekends and holidays are excluded from processing and shipping times, so please account for non-business days when choosing your shipping method. You will receive an email with tracking information when your order has been shipped. Z-Wave Outlet will contact you with a follow-up email if the merchandise you have selected is not currently in stock or if we need additional identification provided for credit verification.

Prepare For Installation / Reset

Please read the user manual before installing the product.

In order to include a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Reset the GD00Z-7 by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.Reset should only be used in the case of a missing or inoperative primary controller.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

An Overview On Garage Door Openers

Without a garage door opener, youd have to manually lift the door every time you needed access, which would be especially annoying if you parked your car in there. A garage door opener is a modern convenience many people take for granted. If your home has an opener already, chances are it was already there when you bought the house. But you dont have to wait until it malfunctions to replace it. In fact, you may find that you can upgrade to a quieter, more efficient model that offers capabilities you dont currently have.

If youve decided you need a new garage door opener, though, where do you start?

Determining horsepower should be the first step in picking out a garage door opener, says Vicki Liston, our home improvement expert and the host of On The FlyDIY, an award-winning show with unique project tutorials. Too much HP and you are wasting a lot of money. Too little and you run the risk of tearing up the motor. The goal is to find the right balance.

She suggests that you may need just 1/3 HP for lightweight single-car garage doors. Light-weight double-car garage doors work most efficiently with 1/2 HP. If you have a door made with a heavier material such as wood, try 3/4, 1 or even 1 1/4 HP or HPc . Basically, the weight and size of your door determine your power needs.

Once youve decided about drive type, its time to delve into the optional features, which make buying a garage door opener a bit more fun.

Don’t Miss: Garage Door Colors For Beige House

What Experts Didn’t Like

Vicki ListonHome Improvement Expert

Vicki Liston writes, produces, and narrates On The FlyDIY, an award-winning home improvement and DIY show of unique project tutorials for the casual DIYer.

Home improvement and all things DIY have been Listons passion since she bought her first house in 2007 and she started making video blogs in 2014. Shes performed hundreds of DIY projects, from small ones to major, wall-smashing renovations and can teach you how to make a trendy DIY barn door for cheap. The proceeds earned from On The FlyDIY are donated to no-kill animal shelters and rescue organizations. You can find her show on Prime Video.

How To Get Alexa To Control My Gocontrol Garage Door Opener

For some reason, altho it shows up in the Echo app, I cant control my opener through the app or my Echo devices all it does is show status. Now that I have an Echo in the garage it would be really handy to be able to tell it to open or close the door. The best idea Ive had is to great a virtual switch in ST, have Alexa turn the switch off and on, and then create an ST routine that controls the door based on the virtual switch. Of course this will only work if the Echo can control the virtual switch. Anybody know if this will work, or have a better idea for how to do this?

You pinned it. Thatll work. Just make sure to toggle back the VS a few seconds later. Or do a momentary switch.

OK so I did try making the virtual switch and it shows up in the Echo app. Looks like I can make a routine that will respond to it and open or close the garage door. Ill test this when I get home. Why do I need to toggle the VS?

Why do I need to toggle the VS?

Lets say that turning the VS on opens the garage. If someone manually closes the garage, your VS will still be on- and that will mess you up on future uses. Better to create routine for if VS changes to ON, open the garage, and then have the VS turn off so its ready for next use. For closing, use a second VS.

You all are trying too hard. I have mine controlled and it works quite well. I use the classic app on android.

In the App, Go to My Home and then tap on your garage door.

Tap the gear in the upper right hand corner

You May Like: Legacy Garage Door Opener Troubleshooting

Gocontrol Garage Door Opener

Im running into some trouble with my GoControl Garage Door opener. It had previously worked with an old garage door. I bought a new door, the installers didn’t hook up the GoControl. It’s a simple device to connect so I thought no big deal. Now I’m close to adding it to the drawer of shame, but decided to ask the community for suggestions before doing so. Ive copied the device log entries below.

Using generic z-wave driver, this is the log messages when I hit open on the device page.

dev:21872020-02-01 11:29:18.979 pm debugzw device: 22, command: 9881, payload: 00 71 05 00 00 00 FF 06 44 00 , isMulticast: false parsed to

dev:21872020-02-01 11:29:18.970 pm infoGeneric Z-Wave Garage Door Opener unable to perform requested operation

dev:21872020-02-01 11:29:18.965 pm debugNotificationReport- NotificationReport

dev:21872020-02-01 11:29:18.313 pm debugzw device: 22, command: 9881, payload: 00 66 03 00 , isMulticast: false parsed to , ]

dev:21872020-02-01 11:29:18.301 pm infoGeneric Z-Wave Garage Door Opener is closed

dev:21872020-02-01 11:29:18.297 pm debugBarrierOperatorReport- BarrierOperatorReport

Device data :

unable to perform requested operation

Means you’re not meeting one of the UL restrictions.

• More than once per minute.
• Audible alert.If the LED is broken the box goes dead, for example. However, the most common problem with them is that they are “hearing” digital data on the Button Contacts.

I know these steps because it’s exactly what I had to do…

Go Control Garage Door Opener

Hello

I only get the correct status of my garage door if i tap the refresh button on the classic smartthings app. Once i tap refresh the correct status is reported. Opening and closing the garage door work just fine. It seems like the status should refresh automatically on the app. Any help is appreciated.

Alix

Has it ever worked? Have you recently put fresh batteries in your gocontrols tilt sensor?

It is working in the sense that once i tap the refresh button on the smartthings app the correct status of the garage door is reported. If i dont tap the refresh button the status is never reported: if the garage door is open , it will say closed until i tap refresh. I will try new battery.

Also Check: Get Rid Of Mice In Garage

Gocontrol Your Connected Home

Enjoy practical and affordable smart home solutions with GoControl products by Nortek Security & Control. The GoControl product line features premium yet simple smart home connected products that give you control over your home and keep you updated on its status from anywhere. Products include smart light bulbs, outlets, switches, garage door controllers, thermostats, and more, all designed to work with the most popular smart home hubs available. Get GoControl products and get ready to GoControl your home!

Please View Our > > simple Returns Page< < For More Details

If the item has a manufacture defect in material or workmanship, we can help you process your Manufacture Warranty Claim. Please contact support@zwaveoutlet.com to trouble shoot your ZWave Outlet Purchase.

Items purchased from outside of ZWaveOutlet.com will need to be processed through their appropriate sales channel ZWaveOutlet’s Guarantee doesn’t cover shipping costs incurred during exchanges and for full refund items need to be in new condition.

We’re so confident we can save you money that we now guarantee it! If you find a lower advertised price from any authorized U.S. dealer on an new, in-stock product, call or e-mail us and well match any verifiable price. You can shop with confidence at ZWaveOutlet knowing you’ll receive the LOWEST PRICE out there, GUARANTEED!

Read Also: How To Insulate The Garage Door

What Is Z

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message and every mains powered node can act as a repeater for other nodes in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.