Liftmaster Garage Door Openers
LiftMaster offers several different options when it comes to garage door openers, all available through Overhead Garage Door. Choose from simple options that include a remote and keypad or more advanced openers with smartphone connectivity and a security camera. Smart garage door openers allow you to use your smartphone as a remote opener by simply downloading the myQ app. These openers also allow Amazon Prime members to have their packages securely delivered to their garage even when theyre not home. Smart garage door openers also work when the power is out, so you can always secure your garage and home.
Constantly worried about an open garage door at night or while youre away from home? Worry no more. A LiftMaster smart garage door opener lets owners program a close timer that will always close your garage door at a certain time. With access from your smartphone, you can close or open your garage door even while at work or on vacation.
Mount The Keypad To The Wall
The Genie GK-R garage door keypad has two screw locations on the back of the unit to mount the keypad to a wall.
It can be mounted to wood, siding, stucco, or brick.
The top screw goes directly into the wall so that the keypad hangs like a picture. The bottom screw goes through the battery panel and into the wall.
Since I was replacing another keypad, I could use the existing screw-holes without needing to drill another.
If youre starting from scratch, use a 3/32 drill bit to drill a pilot hole in the wall.
Tip: The keypad needs to be mounted at least five feet high and away from any of the garage doors moving parts.
Once you have the two holes drilled, hang the keypad from the top screw. Next, remove the batteries and screw in the bottom screw.
Re-insert the batteries and close the battery cover.
Genie Garage Door Opener Programming Instructions
Here at Genie of Fairview Door Co., our customers have relied on us to help install, set up and reprogram garage door opener systems since 1964! Before you call us, though, you may be able to self-diagnose and solve a hand-held remote programming issue on your own.
Programming Genie Intellicode Remote Transmitters
Gently press and release the radio receiver Learn Code button on the Genie of Fairview motor head in your garage. This small, black, usually unmarked button is often located behind the light cover on the motor head and is nearest the 8 inch floppy antenna wire protruding from the head. After pressing this button once, a red indicator light located next to the button will start blinking red for 30 seconds. **
** To erase all Intellicode remotes and wireless keyless entry, gently hold down on the learn button until the red indicator light stops blinking. Proceed to Step 1 above.
For Genie IntelliG, TriloG, SilentMax, Power Max, GPower and PowerLift Series Openers.
These include models 4024, 3024, 4042, 3042, 4022, 3022, and 4046, 3064, 4062, 3062, 2564, 2562. Looking up at the bottom of the Genie motor head cover in your garage you will see a set of black buttons depicted in the drawing belowalong with two LED lights shown here in grey.
Read Also: Garage Door Repair Buford Ga
How Do I Program My New Garage Door Keypad
If you have a keypad outside of your garage that allows you to enter a code to open the door, you can program it using the same learn button you used for the remote. Here are those instructions:
Programming The Keypad For Multiple Openers
If you have more than one garage door opener, the following steps will walk you through the process of adding up to two more openers to the keypad.
Repeat these steps for each additional door enter your current PIN. Press the program key twice the LED will start blinking once per second.
Enter the total number of openers that the keypad will be operating either 2 or 3 push the program key the LED will blink twice and shut off.
Press and hold a programming button or press and release the learn code button on your garage door opener any LED will begin to blink. Enter your PIN on the keypad press the up/down key push the number of the desired door either 2 or 3 press the up/down button three or four times slowly until the garage door operates.
Repeat this step for each additional door step for operating the openers with the keypad for single door operation.
Enter your PIN press the up/down key and the opener will operate for multiple door operations enter your PIN push the up/down key. Press the number key that corresponds with the desired door either 2 or 3 the opener will operate.
Don’t Miss: Best Paint For Garage Door
How To Program A Genie Intellicode Garage Door Opener With Homelink
HomeLink is manufactured by Johnson Controls and allows you to communicate wirelessly between your vehicle and your garage door, gate and more. It is compatible with many Genie Intellicode garage door openers.
HomeLink is manufactured by Johnson Controls and allows you to communicate wirelessly between your vehicle and your garage door, gate and more. It is compatible with many Genie Intellicode garage door openers. Look for the HomeLink logo on your Genie product or in the instruction manual, and also look for the HomeLink logo in your vehicle or in its documentation. Programming involves pushing a few buttons inside the vehicle.
Insert a fresh battery in the Genie Intellicode garage door opener remote. This ensures accurate transmission of the radio frequency.
Turn the ignition on to the accessory setting inside the vehicle.
Press and hold the two outer HomeLink buttons inside your vehicle. Release them when the HomeLink indicator begins to blink.
Place the Genie Intellicode garage door opener remote 1 to 3 inches from the HomeLink surface over your head.
Press and hold the desired HomeLink button and the Genie Intellicode garage door opener remote button simultaneously. Allow the HomeLink indicator to flash slowly and then rapidly. Keep the buttons pressed until this happens.
Resetting The Wireless Keypad
Recommended Reading: Chamberlain Garage Door Opener Adjustment
Why Is The Light Red On My Genie Garage Door Opener
Typically the indicator LED lights on the motor unit when the garage door opener is working correctly. If you notice either or both of the lights flash or have a steady red glow, thats usually an indication of a problem. Here is how to troubleshot the red powerhead lights.
Check this too: Chamberlain Garage Door Opener How-to & Troubleshooting Guide
Genie Garage Door Opener Error Codes Their Meaning And Fixes
The Genie garage door opener has a self-diagnostic status light that sends error codes by flashing a certain number of times to alert you when there is a problem with the opener. The chart below helps you troubleshoot some of the error codes the status light will send.
| Error code |
| The wall control is locked.Slide the Sure-Lock button down to turn vacation mode off. |
Also Check: White House With Black Garage Door
How Do I Reset My Genie Garage Door Remote
So, you have tried everything, and the only thing left undone is to reset the Genie garage door remote. If you are stuck to doing this, here are the steps that you should follow:
For visuals, you can check this demo.
Programming A Wall Console
Programming a Genie wall console is very simple. Just follow these two steps:
Don’t Miss: Access Master Garage Door Opener Troubleshooting
How To Program Your Genie Garage Door Opener
When you purchase a Genie opener from Creative Door, our knowledgeable technicians will help set up everything for you, including the remote control, keypad, and wall console. However, if you ever need to replace or reprogram your Genie opener or are doing a DIY installation, youll require specific information.
The programming instructions we provide in this article are for the following models of Genie garage door openers:
These units all have a large square programming button on the bottom of the opener, beside two up and down buttons. If you have a different type of Genie opener, follow the remote control and keypad programming instructions in your owners manual.
If your opener is one of the above-mentioned models, heres how to program the remote control, keypad and wall console.
How To Program A Genie Garage Door Opener
Genie is another reputable brand when it comes to garage door openers. Through the years, it has released upscale models including wireless ones that could be sync with voice commands via Google or Alexa. If you have older models, you might want to know how to program your Genie garage door opener.
Well, you can do it using a Genie remote control, a keypad or using a wall console. The good part is that these programming types can be done in just four steps each. If you are curious as to how, read on.
In this article:
Related: How To Program Old Craftsman Garage Door Opener
Recommended Reading: Chamberlain Garage Door Remote Opener
Garage Door Opener Remote Troubleshooting Tips
Most of the time, when a remote control stops working, its because the battery has died.
Depending on the model you have, your Genie remote control may take a AAA battery, AA battery, or lithium coin battery. The three-button remote included with most new Genie models take a 2032 lithium coin battery. Heres how to replace it:
If the battery isnt the issue, try reprogramming the remote, following the steps outlined above. You could also refer to the owners manual for the remote control for more troubleshooting advice. If you cant resolve the problem yourself, call in a garage door technician to handle it.
A qualified garage door technician will be able to fix any issues that arise with your keypad or wall console.
Programming A Genie Remote Control
To program your Genie remote, youll need to do the following two things:
Once youve done this, test your remote. The garage door should now open and close when you press the button.
Note that you have 30 seconds to perform each step. If the LED lights on the opener flash red, it means that youve run out of time and will have to repeat the step.
In addition, note that any remote controls that come included with a Genie opener have already been programmed and are ready for use following the installation of the opener. The above instructions are for remote controls that have been purchased separately or that need to be re-programmed.
Read Also: Garage Door Window Plastic Inserts
Programming 971lm And 973lm 371lm And 373lm Security Plus Transmitters
Genie Garage Door Opener Remote Troubleshooting Tips
There are a handful of reasons why your Genie garage door opener remote suddenly stops working. When it does, here are some troubleshooting tips to keep in mind.
| Issue | Troubleshooting tips |
| The garage door opener is opening for no reason. | If you misplaced the remote, you must erase all connected remotes in the main control box. Get a new remote and make sure that it is the only remote programmed in the control box. |
| Remote control is not working. | Check all remotes. If all of them are not working at the same time, the circuit board needs to be replaced. Replace the battery if needed. Replace the Genie remote if needed. Reprogram the remote. |
| Remote works in a limited range. | Remove all sources of interference. Change the battery of the remote. Replace garage light with Genie LED light bulb. |
Read Also: 164th Street Garage Yankee Stadium
Is There A Fuse In A Genie Garage Door Opener
Yes, Genie garage door openers have a glass fuse in the circuit board that protects the opener from damage by shutting off during a power surge. If your garage door is not working, a blown-out fuse is the most common culprit. To troubleshoot a blown-out fuse
- Unplug the garage door opener from the power outlet to avoid electrocution.
- Remove the outer cover on the motor and circuit board.
- Check for signs of burns and melting, such as black burn marks and melted plastic parts or a burning smell.
- Locate the glass fuse and check if it has popped out of its position or it is burnt. A burnt fuse will usually have black soot inside the glass.
- Use a multimeter to test for current and replace it with the same amperage if necessary.
How Do You Program A Genie Opener
Now that the Genie opener is clear of all remote controls, you must reprogram the following devices to run the garage door correctly. For the proper operation of your garage door opener, there are three programming functions you must set.
You have to complete each programming step within the 30 second time limit, after which two LEDs will turn red, indicating the time limit has expired, and you must restart.
Also Check: Garage Door Wall Button Flashing