Genie Garage Door Opener Remote Program

Share This Post

Genie Garage Door Opener Remote Troubleshooting Tips

Genie Remote Control Programming (Full video)

There are a handful of reasons why your Genie garage door opener remote suddenly stops working. When it does, here are some troubleshooting tips to keep in mind.

Issue Troubleshooting tips
The garage door opener is opening for no reason. If you misplaced the remote, you must erase all connected remotes in the main control box. Get a new remote and make sure that it is the only remote programmed in the control box.
Remote control is not working. Check all remotes. If all of them are not working at the same time, the circuit board needs to be replaced. Replace the battery if needed. Replace the Genie remote if needed. Reprogram the remote.
Remote works in a limited range. Remove all sources of interference. Change the battery of the remote. Replace garage light with Genie LED light bulb.

How To Program Garage Door Opener Remote

We will teach you everything you need to know about your garage door remote and will show you how you can program garage door opener for Liftmaster, Chamberlain, Craftsman, and Genie.

Garage door opener remotes are a convenience most of us take for granted. They allow us to enter and exit our garage without needing to leave our car or remember an entrance code.

However, these remotes can break, or wind up lost or stolen. If this happens, you need to know how to program your remote so you can get back into your garage.

Today, well outline precisely how to accomplish this.

Need Help With An Old Garage Door Opener

If you have a garage door opener that youre happy with but need some maintenance or repairs done, dont forget that Overhead Garage Door is able to handle a wide range of garage door needs. From programming remotes and keypads to help figuring out the LiftMaster smartphone app, we are happy to help.

Our garage door services include:

  • Help with garage door visual and motion sensors.
  • Hinge repair and replacement.

Read Also: Garage With Lift For Rent

How Do I Reset My Genie Garage Door Remote

So, you have tried everything, and the only thing left undone is to reset the Genie garage door remote. If you are stuck to doing this, here are the steps that you should follow:

  • First, press the learn button from the main control box.
  • Now get your remote control and point it on the control box. Press the open button on the remote opener three times.
  • Now press the open button and test if the process worked. The LED light should blink. After the blink, the garage door should open. If it does not work, you have to repeat the steps.
  • For visuals, you can check this demo.

    How To Reset A Genie Garage Door Opener

    Universal 4 Button Garage Door Opener Remote

    This article was co-authored by wikiHow staff writer, . Janice is a professional and creative writer who has worked at wikiHow since 2019. With both a B.A. and M.A. in English from East Stroudsburg University, she has a passion for writing a wide variety of content for anyone and everyone. In her free time, you can find her working on a new crochet pattern, listening to true crime podcasts, or tackling a new creative writing project.There are 8 references cited in this article, which can be found at the bottom of the page. This article has been viewed 203,912 times.Learn more…

    Genie garage doors are known for their convenience and easy-to-use remotes. Unfortunately, this system becomes less simple when you need to sync or resync your remote. If you have a wireless keypad, you may also need to recalibrate this device if it doesnt open your garage door properly. With the push of a few buttons, you can reset either your Genie opener or wireless keypad in a matter of minutes.

    You May Like: Universal Garage Door Remote Walmart

    Programming Multiple Genie Garage Door Openers To A Keypad

    This step assumes you have already changed the keypads default pin and have programmed at least one Genie garage door to the keypad. Then, follow these steps to program the other remotes.

  • Enter the keypad pin.
  • Press the Program key twice until the LED starts blinking slowly.
  • Enter either 2 or 3 as the number of garage door openers this keypad will service.
  • Press the Program key once to confirm the value.
  • The LED will flash twice and turn off.
  • Proceed to step 7 below to add the additional garage door opener to this keypad.
  • Put the next garage opener in programming mode by setting the button on the opener unit marked as Program,Learn, or Set.
  • Enter the access pin on the keypad.
  • Press the Up/Down key on the pad once.
  • Press the door number of the opener you are programming, for example, 2 or 3.
  • Now, press the Up/Down key about four times.
  • The garage door opener will start to function.
  • Genie Garage Door Openers In Western Canada

    Creative Door ServicesTM carries and installs top-quality Genie garage door openers in British Columbia, Alberta, Saskatchewan, and Manitoba. Trust our experienced team with all your garage door operator installation, repair, and maintenance needs. Contact us to learn more about our garage door products and services.

    Recommended Reading: Learn Button On Chamberlain Garage Door Opener

    What To Do If Programming Your Remote To The Opener Is Not Successful

    • If you cannot program your remote to your opener, you could have a faulty garage door mother board or bad remote. It might also be a bad battery in the remote
    • If your opener is multi-function, it may also be programmed to control your garages lights or other features.
    • If the garage door remote will work, but intermittently, that means the programming was still successful. A bad remote or circuit board might be a problem.

    This is a quick and easy way to program a garage door remote to any Genie garage door opener of the following models:

    • 1028, 1028H, 2028, 2028H
    • 1128, 1128B, 2128, 2128B
    • 2035, 2055, 3035, 3055
    • 3022, 3024, 3042
    • 4022, 4024, 4042

    Resetting The Wireless Keypad

    Genie Garage Door Remote Programming 2 Easy Steps
  • 1Find the up/down and program keys and press them down for 5 seconds. Locate the button labeled “Program” on the top of the wireless keypad, along with the up/down button on the bottom. Press down both of these buttons simultaneously for about 5 seconds. When it has been reset successfully, the LED on the keypad will blink twice, and the entire device will go dark.XResearch source
  • After you do this, any pre-existing keypad code wont be able to open up the garage door.
  • 2Press 3, 5, and 7 in succession after the opener is in programming mode. Push down the square “Program Set” button on the opener for at least 3 seconds to get it into programming mode. Push down the “3,” “5,” and “7” buttons in sequential order on the wireless keypad to start the programming process. This is the default code for all Genie garage keypads that are still using their factory settings.XResearch source
  • 3Push the up/down button 3 times to open the garage door. Find the up/down button on the keypad, located toward the bottom of the device. After youve pressed “357” into the keypad, slowly push the up/down button until the garage door moves. To double check and see if the keypad has synced correctly, input “357” into the device again and hit the up/down button. If the garage door opens or shuts, then youre good to go!XResearch source
  • Don’t Miss: Plastipro Loc Heavy Duty Garage Floor Tiles

    Programming A Genie Garage Door Opener To A Remote Control

    The remote control is the default programming tool for garage door openers. Genie has different remotes, for example, the G3BT, the GM3T, the GIT, and the GT912. In addition, there are the New Genie Openers and the older models dating from 1995 to 2011.

    Follow the steps below carefully:

  • Put the garage opener in programming mode by setting the button on the opener unit marked as program or set.
  • Hold this button for at least about 3 seconds for the newer Genie models. Be on the lookout for two LED lights. The small button will turn blue, and the more extended button will be purple.
  • For the older Genie models Press and then release the Learn Code button once until the red LED light flashes.
  • Pair the remote with the opener.
  • Do this step within 30 seconds after step 1. Get your remote control and ensure you stand at least five feet away from your garage door. Push and then release the desired button on your remote control twice.
  • Next, you will see the LED lights blink and then turn off.
  • Press the same button for the third time to test and open your garage door.
  • Lastly, if you take too long, the garage opener unit will flash red, and you should redo the process.
  • How To Program A Genie Garage Door Remote Intellicode Model H6000a

    Genie manufactures a variety of remote controls compatible with the Intellicode system that will operate your opener once you program the remote to communicate with the opener motor. Programming your Genie Intellicode model H6000A garage door remote becomes necessary when adding a second remote, replacing a lost remote, changing remotes for new tenants or after retaining ownership of the home from the previous owners.

  • 1.

    Look above your Genie garage door opener for the two screws holding the light bulb cover to the front of the motor. Remove the screws and lower the cover.

  • 2.

    Find the learn button to the left of the light bulb socket. Depress the learn button and quickly release it. The red LED beneath the learn button will blink twice each second once you release the button.

  • 3.

    Press the button on your remote within 30 seconds of releasing the learn button. The red LED beneath the learn button will stop flashing and remain lit. Press the remote control button once again to complete the programming and extinguish the red LED.

  • 4.

    Raise the light bulb cover on the Genie opener motor. Secure the cover with the two screws you removed.

  • References

    Tips

    Writer Bio

    Don’t Miss: Benjamin Moore Garage Floor Paint

    Professional Garage Door Repair Services

    With a dedication to safety and customer satisfaction, you can trust ProLift Garage Doors for all of your garage door repair needs. You cant always plan ahead for garage door problems, but you can count on us to respond when you need us: right away. Call today to fix your residential garage door emergencies and work with us to maintain or replace your current garage door to prevent future problems.

    Programming A Single Genie Garage Door Opener To A Keypad

    Digi Code 5040 300 MHz Garage Door Gate Opener Remote Control Multicode ...

    The following steps outline the keypad setup for a single garage door opener. If you have not changed the default keypad pin yet, use the default pin.

  • Put the garage opener in programming mode by setting the button on the opener unit marked as Program or Set.
  • Ensure the keypad backlighting is off and remove the protective tab from the battery holder
  • Enter the default pin 3-5-7 on the keypad. See section changing the pin code.
  • Next, push the up/down keys about four times until the LED light turn purple and switches off
  • Press the button to operate the garage door
  • You May Like: Genie Program Garage Door Opener

    How To Program Your Genie Garage Door Opener

    When you purchase a Genie opener from Creative Door, our knowledgeable technicians will help set up everything for you, including the remote control, keypad, and wall console. However, if you ever need to replace or reprogram your Genie opener or are doing a DIY installation, youll require specific information.

    The programming instructions we provide in this article are for the following models of Genie garage door openers:

    These units all have a large square programming button on the bottom of the opener, beside two up and down buttons. If you have a different type of Genie opener, follow the remote control and keypad programming instructions in your owners manual.

    If your opener is one of the above-mentioned models, heres how to program the remote control, keypad and wall console.

    How To Program A Genie Garage Door Wall Console

    The wall console is a small device mounted on your wall or low in the floor. Here is how to program the Genie garage door wall console.

  • Press the program button. Hold it down until the LED light turns blue and then shuts off. The longer LED light should turn purple.
  • Next, press the door button on the console. Do it every two seconds until the garage door opens.
  • Related: How To Program A Liftmaster Garage Door Opener

    Read Also: Double Wide Mobile Home With Attached Garage

    Overhead Garage Door Has You Covered

    If you purchase a new garage door or opener from Overhead Garage Door, we will handle the purchase, delivery, installation, and service. If you purchase one of our new garage doors for sale, our team will even deal with programming the opener for you.

    Contact Overhead Garage Door for all of your garage door needs. We offer a wide selection of brands so you can find the perfect door to match your home, your needs, and your style. We also provide installation and repair service so you know your garage will be taken care out from beginning to end. Serving the greater Chicago area and northern Illinois since 1969, we provide 24-hour service, emergency response, and same-day appointments to keep your home secure and your garage door working properly.

    Universal Home Remote For Homelink Or Car2u In

    How To Program Your Genie Garage Door Opener and Remote Control.

    Programming a Rolling Code Garage Door Opener

    If your in-car remote has 3 LED lights, one above each button, you should follow the instructions below to program your Rolling Code Garage Door Opener.

  • Press the outer two in-car buttons simultaneously for 2 seconds and release .
  • Place the garage door opener into learn mode by pressing the small square colored button, or the small round black button on a Genie, located behind the light bulb globe in the garage. This may require the use of a ladder, follow all safety precautions.
  • The LED on the garage door opener will go on immediately. For Genie openers the LED will begin blinking.
  • Press and hold the button on the in-car remote that you want to use for operation of the garage door to activate.
  • Watch for the garage door to activate.
  • When the garage door activates, release the button and depress again the selected button to lock in the program.
  • Programming of Rolling Code garage door opener is now complete.
  • Programming a Fixed Code Device

    Below is a picture of a typical 12-switch DIP switch layout located on your hand-held remote control under the battery cover . Note: Genie, Linear, Multi-Code and Stanley have only 2 position switches: up or down.

    1

    You May Like: Parts For Craftsman Garage Door Opener

    Program A Genie Remote Control:

    Generally, the company provides a pre-programmed remote control with a garage door opener. If you want to re-program or you have purchased an additional one follow the below steps to program it.

    Step 1: For the new remote, just remove the protective film from a remote battery. Thats a quite easy one.

    Step 2: there is a program button on a Garage door opener remote press & hold it for 2 seconds. The round LED will be turned blue and then release. Then after you will see a long purple LED flashing.

    Step 3: Press & hold a remote button two times. You will see the LEDs on an opener flashing that indicates your remote has been programmed successfully.

    Thats it. Now just press the Garage door opener remote button again & you can open and close the garage door.

    Still, need help to program the remote control of these two brands or seeking guidance to re-program the remote of other brands? The garage door repair and installation experts are here to help you at any time. Contact us today and get your garage door issues resolved as soon as possible.

    Schedule an appointment today or fill up the contact form.

    Identify The Learn Mode Or Program Mode Button

    On some Genie Garage Door Openers, three buttons sit on the control panel. The learn or set button is a large square button next to the LED indicators. Beside the square, two triangular buttons point up or down, allowing you to cycle up or down through your functions. You can also use them to raise or lower the garage door when you only want it partially open.

    While youre exploring the buttons, look at the lights as well. On the model were using as a sample, two LED indicators sit beside the square button. One is a long vertical indicator while the other is a small circular one. Both lights alternate between off, steadily on, and blinking. These modes are a key part of your programming process, so pay attention to them.

    Read Also: Garage Shelving At Home Depot

    How Do I Replace A 2032 Lithium Coin Battery For My New Genie Garage Door Opener

    Newer models of Genie garage door openers are operated by a 2032 lithium coin battery and here is how you replace it:

    • Get a screwdriver and disassemble the battery slot by opening the remote case.
    • Access the circuit board by carefully removing the touchpad. Flip the circuit board. There you will find the battery compartment.
    • Push the lithium battery out of the compartment using a flat screwdriver.
    • Replace it with a new one and then reassemble the remote.

    Next Get Your Remote Control And Stand Five Feet Away From The Garage Door Opener

    LiftMaster 375UT Universal Gate or Garage Door Opener Remote Control

    Press and release the button in the remote control that you want to use. Do it twice. The LED lights in the garage door opener should blink and then turn off. If it does this, the garage door opener can now be opened and closed using your remote control.

    *Note: You have a 30-second window time to accomplish each step. Once the garage door openers lights turn red, you must repeat the process.

    Recommended Reading: Roll Up Garage Door Prices

    Related Posts