Programming A Genie Keypad
These instructions are for linking a Genie keypad with a Genie opener for a single garage door. If youre linking the keypad to more than one garage door, the process will be different. Refer to the keypad owners manual for instructions.
To program your Genie keypad, follow these three steps:
The keypad is now ready to use. When you put in the code and press the up/down button, the garage door will open. Note that after you open or close the door with the keypad, you can cause the door to stop and reverse by pressing any button while the doors still in motion.
So Here Are Steps To Follow Of How To Reprogram Genie Garage Door Keypad
- Take out the light cover of the device installed inside the garage door by unscrewing it using ladder.
- Now getting back to the genie keypad for reset the old code by reprogramming.
1- Hold Program button with Digit 6 and up/down button at a same time.
2- And then Press 3, 5, 7 and then press Program button.
3- Next step is to reset pin by pressing whatever you want the code For example press 2344 and then press Program button and wait for the red lights to blink couple of times and then it will goes off.
4- Next step is to go back to your garage door opener hit the Learn Button and you will see red light blinking below learn button.
After Hit the learn button you have a 30 second for verifying the code.
5- Go back to Keypad and press the new CODE 2344 and press up/down button.
6- Then go back to Garage door opener and you will see the red light blinking turn a solid red color.
7- After you confirm about the solid red color you again have a 30 seconds timeframe, so go back to Keypad and press UP/Down Button.
8- Note: Before testing your new reprogram code, you have to wait until the two backlit keypad lights turn off.
You have to go through the whole process again. If you test the code before turning off the keypad back lit light.
Programming A Single Genie Garage Door Opener To A Keypad
The following steps outline the keypad setup for a single garage door opener. If you have not changed the default keypad pin yet, use the default pin.
Read Also: Home Depot Garage Overhead Storage
Change The Garage Door Keypad Pin
You dont want to operate your garage door opener with the factory default pin. Anyone with a similar garage door keypad will know the number and can access your home through the garage with it.
To change the pin, follow these steps in one sequence:
- Enter the current pin , the factory default pin that comes with your unit.
- Press the program button
- Enter your preferred pin consisting of three to eight digits
- Press the program button again
Once you finish this sequence, the LED indicator and backlight will flash a few times before going off.
This indicates that you have successfully changed the access pin to your garage, with your new pin replacing the original factory default pin.
The video below shows how to program genie garage opener keypad in 3 simple steps
Genie Garage Door Openers In Western Canada
Creative Door ServicesTM carries and installs top-quality Genie garage door openers in British Columbia, Alberta, Saskatchewan, and Manitoba. Trust our experienced team with all your garage door operator installation, repair, and maintenance needs. Contact us to learn more about our garage door products and services.
You May Like: Garage Door Opener Craftsman 1 2 Hp
Pair The Keypad To Your Genie Garage Door Opener
The default access code for your Genie garage door keypad is 3-5-7.
With your garage door opener still in programming mode, ensure that your keypad is NOT lit up before starting.
- Press the default code or your new code if you have already changed it.
- Press the Up\Down button on the keypad slowly until the garage door opener operates.
How To Install The Genie Gk
From start to finish, I installed and programmed my new Genie GK-R garage door opener keypad programmed within 15 minutes. That included the time it took to take pictures for this article, so this truly is something you can do quickly and easily.
Genie recommends that you program the wireless keypad before mounting it to the wall.
Don’t Miss: Garage Door Repair Durham Nc
Quick Facts About The Genie Gk
- Genie is owned by the Overhead Door Corporation and is based in Ohio.
- The GK-R keypad provides keyless garage access for up to three different Genie garage door openers.
- It can use anywhere between 3 8 digits for your PIN.
- It works with all Genie garage door openers with Intellicode security technology manufactured since 2011 and many manufactured before then.
- You can use it outside because it has a flip up cover to protect against the elements.
- Uses 2 AAA batteries
Programming A Genie Garage Door Opener Wall Console
The Genie wall console is typically a three-function device controlling the garage door opener. Follow the steps below to program the console to the garage door opener.
Read Also: 4 Post Garage Car Lift
The Process May Be Easier If You Have An Assistant Or Helper Enter The Code If The Keyless Is Already Mounted On The Wall
Genie garage door opener keypad forgot pin. Genie garage door opener remote gm3t bx genie remote control programming full you genie 3 on garage door opener remote with intellicode programming homelink to newer genie openers you. 3) enter the pin number you want to use, pres prog and the indicator will now blink twice per second.
How To Program Additional Remote Controls To A Genie Opener
Follow these steps to program optional control transmitters other than those provided with the garage door opener. Ensure that you stand at least five feet from the garage door opener.
Read Also: How Much To Install Tesla Charger In Garage
Can I Reprogram An Old Garage Door Opener
Did you misplace your garage door opener remote? Or maybe you need to change the keypad code. Whatever the reason, you can easily reprogram an old garage door opener. If you need to program a new remote that replaced a lost one, simply follow the same instructions above for programming new remotes. The connection to the new remote will override the old one, even if you manage to find the old remote later on, so you dont have to worry about a stranger finding the old remote and gaining access to your garage.
Reprogramming a garage door keypad is as simple as programming a new keypad. Using that same learn button, you can enter a new code that will override the previous code. Follow the instructions above for programming a new keypad.
If you have questions or concerns while attempting to program or reprogram a garage door opener, dont hesitate to call Overhead Garage Door. We have professionals always ready and happy to help.
Final Thoughts On How To Program Genie Garage Door Keypad
Whether it is a new or trusty old keyless entry pad for your garage door, programming a Genie garage door keypad is straightforward. You just need to know the simple steps to follow to complete the task.
Always start by resetting the memory of your keypad to its factory default before setting up a new pin and synching it with your garage door opener or multiple openers.
We hope this guide helped you out. If you have any thoughts or comments, leave them in the comments, and we will do our best to respond at the earliest.
Read Also: Insulating Floor Over Unheated Garage
Enter The Programming Mode
Locate the learn button on the garage door openers motor unit. This is the programming button used to pair the keyless pad to the opener.
The learn button on your Genie garage door opener can be on the down-facing side under the light bulb cover or at the back of the motor unit. If the button is at the back of the motor unit, it will face away from the garage door.
An easier way to locate this button is to check the garage door openers label, your operators instruction manual, or the current remote.
Your Genie garage door opener can have a small cylindrical learn code button or a larger square programming button.
You may require a ladder to reach the button as the opener motor units usually sit at a significant height from the ground.
Once the unit is in its programming mode, you will have 30 seconds to pair it with the keypad unit to be installed outside the garage door.
How To Program A Garage Door Opener
A faulty garage door opener isnt just annoying it can leave your home vulnerable, too. If you need to learn how to program a garage door opener, there is help. You can easily program the opener yourself or, if youre having trouble, you can reach out to a professional. Heres what you need to know about programming a garage door opener.
Recommended Reading: Garage Door Opener Remote Replacement
S Of The Genie Garage Door Keypad
To program your Genie garage door keypad successfully, you first need to understand the anatomy of the keypad. Specifically, the keypad has various indicators and buttons with different roles.
Once you know the role of each button and indicator, programming and operating the garage door opener using the unit should be a breeze.
If you have a problem with a program or enter an invalid pin, the program key, LED indicator, and numbered keypad will flash rapidly. You will have to wait fifteen seconds before you can make the correct entry when this happens.
You can tell when you make the correct entry by observing the three indicators. The program key and the LED indicator will flash slowly while the numbered keypad backlight remains on for 15 seconds. This indicates a valid pin number or successful program has been entered.
Programming Multiple Genie Garage Door Openers To A Keypad
This step assumes you have already changed the keypads default pin and have programmed at least one Genie garage door to the keypad. Then, follow these steps to program the other remotes.
Recommended Reading: East West Parking Garage Moda Center
How Do I Program My New Garage Door Opener Remote
Image via Pexels by Jaymantri Licensed CC0
When programming a remote garage door opener, youll need to start by locating the learn button on the power box that connects to the garage door. Here are step-by-step instructions:
Programming Car2u To A Genie Garage Door Opener
The Car2U device has a default factory setting, with button 1 being the Genie Openers. Follow the steps below to program Car2U to a Genie garage door opener.
Read Also: Whisper Drive Garage Door Opener
Programming A Genie Remote Control
To program your Genie remote, youll need to do the following two things:
Once youve done this, test your remote. The garage door should now open and close when you press the button.
Note that you have 30 seconds to perform each step. If the LED lights on the opener flash red, it means that youve run out of time and will have to repeat the step.
In addition, note that any remote controls that come included with a Genie opener have already been programmed and are ready for use following the installation of the opener. The above instructions are for remote controls that have been purchased separately or that need to be re-programmed.
Mount The Keypad To The Wall
The Genie GK-R garage door keypad has two screw locations on the back of the unit to mount the keypad to a wall.
It can be mounted to wood, siding, stucco, or brick.
The top screw goes directly into the wall so that the keypad hangs like a picture. The bottom screw goes through the battery panel and into the wall.
Since I was replacing another keypad, I could use the existing screw-holes without needing to drill another.
If youre starting from scratch, use a 3/32 drill bit to drill a pilot hole in the wall.
Tip: The keypad needs to be mounted at least five feet high and away from any of the garage doors moving parts.
Once you have the two holes drilled, hang the keypad from the top screw. Next, remove the batteries and screw in the bottom screw.
Re-insert the batteries and close the battery cover.
You May Like: Best Upright Freezer For Garage 2021