Craftsman 1/2 Hp Chain Drive Garage Door Opener Installation

My Remotes Will Not Activate The Door

Craftsman Garage Door Opener Assembly

Verify your door control is not blinking. If it is blinking, deactivate the Lock Mode by pressing and holding the Lock button for several seconds.

Reprogram remotes following the programming instructions.

If the remote will still not activate your door, check the diagnostic LED for flashes on the motor unit, then refer to Diagnostic Table.

Page : Using The Wall

Page 32 CARE OF YOUR OPENER THEREMOTE CONTROL B ATTERY LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause To prevent possible SERIOUSINJURYor DEATH: FORCE CONTROLS some minor changes in door NEVERallow small children near batteries. operation requiring some If battery is swallowed, immediately notify doctor. re-adjustments, particularly To reduce risk of fire, explosion or chemical burn: during the first year of operation.

The Transmitter Has A Short Range

Check battery test light If the light is dim, change the battery

Change the location of the transmitter in the car.

A metal garage door or foil-backed insulation or metal siding will reduce the transmission range Antenna extender kit is available from any Sears Store or Service Center.

Check to be sure the antenna on the back panel of the opener extends fully downward.

Don’t Miss: Keep Flies Out Of Garage

How Do You Know That You Need A Garage Door Spring Repair

As your garage door ages, it becomes less effective. The steel loses resiliency and the door begins to weigh more. When springs are brand new, you just need around 10 pounds of force to lift and open the door. But when springs move towards the end of their lifespan, owners need to apply more force to lift the door, almost as much as the doors weight.

Aging springs increase the load laid on a garage door opener. So, another sign indicating that you need to go for spring repair is when you hear the electric door opener straining as it tries to open the door.

Aging door springs can cause significant damage if they break suddenly. This is because they shut violently. If you are around when the spring breaks, you will hear a loud gunshot-like sound. The break usually occurs when the spring is fully loaded – twisted or stretched to its full tension. In the case of a broken spring, the door will be extremely heavy when you try to open it on your own and the automatic garage door will completely fail to lift the door.

/2 Hp Chain Drive Garage Door Opener Kit

CHAIN DRIVE: Rugged steel construction delivers toughness and durability you can count on
LIFT POWER: Reliable Lifting Force of ½ HP is ideal for light daily use on a 7 ft. garage door extension kits are required for an 8 ft. door or for a 10 ft. door
SECURE ACCESS: Each time the remote is activated, a new access signal is sent from billions of possible combinations to prevent interception of the radio signal by would-be hackers

You May Like: Home Depot Garage Door Installation Cost

About Sears And Craftsman

Sears originally established the Craftsman house brand to produce a lint of tools related to home improvement, lawn and garden equipment, and work-wear.

The tools were first made available for the public in 1927 via a Sears catalog, and later on, through other retailers. One of the best things about most Craftsman hand tools is that they include an unlimited lifetime warranty that requires no receipt or dated proof of purchase.

Not to mention, Craftsman garage door openers are quite a hit with the buyers, and they even have a place of honor on the Amazon’s Choice’ list.

Chain Drive Garage Door Openers

Chain drive garage door openers use a metal chain to open/close the garage door, in conjunction with moving gears. The metal chain assembly unit is attached to tension springs that help lift the garage door.

This type of garage door is more popular because it’s more affordable and readily available. Craftsman chain drive door openers also include a remote control with a frequency range of over 1000 ft. and WiFi capabilities .

Recommended Reading: Garage Door Openers At Walmart

Craftsman Garage Door Openers Repair And Installation

Craftsman garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive with Assurelink ®.

About Craftsman Garage Door Openers

Craftsman is characterized by durability, innovation and consistency. From hand tools to power tools and from lawn and garden equipment to tool chests and other storage solutions, Craftsman products are built to last and designed to give you the confidence to complete any project no matter the size. Also known for its unlimited lifetime warranty on hand tools, Craftsman is a leader in professional-grade tools for carpentry, automotive, electrical, plumbing and other vocations where tool reliability and ingenuity are the keys to success.

Craftsman Garage Door Opener Products

Craftsman Garage Door Openers are Americas favorite. There are several options to choose from to fit your individual needs. Craftsman garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Assurelink garage door opener which allows you to control and monitor your garage door even when you are away from home.

Craftsman Garage Door Opener Repair and Installation

Page 2: Fasten The Door Bracket

How to Install a 53985 Craftsman 1/2 hp Garage Door Opener Craftsman ½ HP 54985

Page 24 ONE-PIECE D OORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.

Page 25 INSTALLATION STEP Figure 1 Pulley Connect Door to Trolley IL_. 8″ min, Follow instructions which apply to your door type as _amlmllmo illustrated below and on the following page. Trolley / /O -“/’t Outer stopBo,t /,nne,! SECTIONAL DOORS ONLY Trolley Ring …

Also Check: How To Program Liftmaster Garage Door Opener To Car

Page : Cuelgue El Abridor

Page 55 |NSTALAC|ON, PASO Irestale Unidad Control Para evitar la posibilidad de una LESIONGRAVEo INCLUSOLA MUERTEpor electrocuci6n: Puerta ANTES de instalarel control de la puerta, cerci6rese de que la energia el(_ctricaNO est_ conectada. Ubique el control de la puerta de manera que quede a la …

The Ultimate Guide To Garage Door Spring Repair

A garage door spring balances the weight of a garage door and enables easy movement – opening and closing manually or automatically. It is made of high-tension steel, which has a limited lifespan and loses its effectiveness with time. Garage door springs have different quantity levels such as 10,000-use or 20,000-use. Many buyers feel that this is quite a large number but when you evaluate and analyze, you will realize that a garage door is probably opened four to five times a day, every day, every year justifying the high quantity levels.

Also Check: Garage Door 7 X 9

Craftsman Garage Door Opener Model 53920 Features

Horsepower: 1/2Light Source: 75 watts with 1 Light Bulb

Security Features:

Security+® anti-burglary remote controls with rolling codes
PosiLock® system to secure the garage door when it is closed

Safety Features:

Safety Sensor Infra-red beam
Sensing technology to stop and reverse the garage door if a person or object is contacted
Manual door release capability

Limited 4-year warranty on the motor

Special Features:

PosiLock® system to ensure the door stays locked when it is closed

Options:

Rail extension kits for 8 foot and 10 foot high garage doors
Extended warranty Protection Agreement from Sears
Installation Service

Sears Craftsman Garage Door Opener Manuals

1/2 HP Chain Drive Garage Door Opener Kit

It can sometimes be difficult to find the correct instruction manual for your device, particularly for older, discontinued models.

Use the search bar below to find your specific Sears Craftsman Garage Door Opener Manual. You can enter the model number, name or description. Weve also included images to help.

If you have a manual you would like to list, submit it here. Or, if your model is not listed, leave a comment below.

You May Like: Commercial Garage Door Size Chart

/2 Hp Chain Drive Garage Door Opener Kit With Myq

SMARTPHONE CONTROL: With built-in Wi-Fi, you can monitor and control your garage door from anywhere at anytime using the myQ® app
CHAIN DRIVE: Rugged steel construction delivers toughness and durability you can count on
LIFT POWER: Reliable Lifting Force of ½ HP is ideal for light daily use on a 7 ft. garage door extension kits are required for an 8 ft. door or for a 10 ft. door

Install The New Chain And Cable Assembly

Lay the new chain and cable assembly beside the rail.

Grasp the end of the chain cable and pass approximately 12 inches of cable through the rail window.

Add general-purpose grease to the idler pulley center hole if it’s dry.

Insert the idler pulley into the rail window behind the chain cable and line up the mounting hole.

Reinstall the idler pulley bolt and tighten it firmly with the lock washer and nut.

Make sure the idler pulley spins freely after tightening the nut.

Connect the chain cable to the retaining slot by pushing the pins of the master link bar up through the cable link and trolley slot.

Push the master link cap over the master link bar pins and past the pin notches.

Slide the clip-on spring over the master link cap and onto the pin notches until both pins are securely locked in place.

Position the inner trolley to the previously marked position on the rail.

Align the rest of the chain and cable assembly along the rail, routing the cable onto the idler pulley and threading the chain through the chain spreader and around the motor sprocket, making sure not to twist the chain.

Connect the trolley threaded shaft to the new chain by pushing the pins of the master link bar up through the threaded shaft mounting hole and the end link of the new chain.

Push the master link cap over the master link bar pins and past the pin notches.

Slide the clip-on spring over the master link cap and onto the pin notches until both pins securely lock in place.

Read Also: 2 Hp Garage Door Opener

Craftsman Garage Door Opener Hp Chain Drive 2 Security+ 3

In search for a trusted high-powered garage door opener that could noiselessly lift any type of garage doors heaviest or lightest and has a three-way button that could access your garage doors from long distances? Youre in for a great deal with Craftsman Garage Door Opener 1/2 Hp Chain Drive, 2 Security+® 3-Function Remote Controls.

The Door Reverses For No Apparent Reason

Installed a Craftsman Garage Door Opener

Is something obstructing the door? Pull the red emergency release handle Operate the door manually If it is unbalanced or binding, call a garage door serviceman to correct the problem

Clear any ice or snow from the garage floor area where the garage door closes

Review the Force Adjustment Chart. REPEAT SAFETY REVERSE TEST after adjustment is complete.

If door reverses in FULLY CLOSED position, decrease travel limits

The Infrared Reversing Sensor may be misaligned or obstructed. Disconnect the sensor and check door operation ff the problem disappears, correct alignment

Don’t Miss: Chamberlain Keypad Garage Door Opener

Craftsman Garage Door Opener Model 53920

Like other Sears garage door openers in the chain drive category,the Craftsman model 53920 has a strong 1/2 HP motor and a rugged chain drive

The Craftsman garage door opener model 53920 is a basic 1/2 HP chain drive garage door opener. The model 53920 is inexpensive with simple features, but it gets the job done. In the 1970s this would have been the top of the line model, but todays feature-driven world has raised the bar, so to speak.

Like other Sears garage door openers in the chain drive category, the Craftsman model 53920 has a strong 1/2 HP motor and a rugged chain drive, so this is no slouch when it comes to lifting your single or double car garage door. Keep in mind, however, that you may want to consider a 3/4 HP model like the Craftsman Model 53990 if you have a very heavy carriage house door or solid wooden garage door.

Craftsman 1/2 HP Chain DriveGarage Door OpenerModel 53920

The Craftsman garage door opener model 53920 carries the same safety and security features of other Sears models, including Security+® anti-burglary rolling code technology, sensing technology to reverse and open the garage door when it encounters a person or object, and the PosiLock® feature that keeps the garage door locked once it is closed.

Page 5: Instale La Sistema De Protecci6n

Page 59 INSTALACION DE LAS MI_NSULAS Figura INSTALAClON EN ELCARRIL DE LA PUERTA Asegdrese de que el abridor no estd conectado a la corriente eldctrica. Carril de Instale y alinee las m_nsulas de manera que los sensores est_n uno frente al otro en los lados opuestos de la puerta, a una Reborde distancia maxima de 15 cm del piso.

Page 60 MONTAJE Y CABLEADO DE LOS SENSORES Figura Tuercade mariposa SISTEMA DE SEGURIDAD DE REVERSA Deslice la cabeza de un perno de coche de 1/4-20xl/2 pulgada dentro de la ranura de los sensores. Use tuercas de mariposa para sujetar los sensores alas m_nsulas, con las Pernode coche “_ lentes de cada sensor frente a frente a ambos lados de la…

Read Also: Genie Garage Door Openers Remotes

Page : Install The Protector System

Page 21 INSTALLING THE BRACKETS Figure 1 DOOR TRACK MOUNT Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other Door across the garage door, with the beam no higher than 6″ Track above the floor.

Page 22 MOUNTING AND WIRING THE SAFETY REVERSING Figure 5 SENSORS Wing Nut Slide a 1/4″-20xl/2″ carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by CarriageBolt —-_ a bracket extension .

Opener Strains Or Maximum Force Is Needed To Operate Door

1/2 Horsepower Chain Drive Craftsman Opener

The door may be out of balance or the springs are broken. Close door and use emergency release rope and handle to disconnect trolley Open and close door manually A properly balanced door will stay in any point of travel while being supported entirely by its springs if it does not, call a garage door sen/iceman to correct the problem.

You May Like: Garage Doors San Antonio Tx

Reinstall The Garage Door Opener

Reconnect the rail end to the header bracket using the clevis pin and fastener ring.

Position your step ladder under the motor unit ceiling bracket and carefully set the motor unit on top of the step ladder.

Climb the step ladder and reinstall the motor unit to the ceiling bracket using the nuts, bolts and lock washers.

Open the light cover to access the wall control and safety sensor terminals on the motor unit.

Using your digital photo for reference, reconnect the wall control and safety sensor wires to the motor unit.

Close the light cover.

Take The Garage Door Opener Down

Pull the emergency release rope to release the trolley from the garage door.

Shut the garage door if it’s not already closed.

Remove the fastener ring from the straight door arm connected to the outer trolley.

Pull out the clevis pin while supporting the straight arm to disconnect the garage door from the outer trolley.

Lower the straight and curved arms and rest them against the garage door. Use a helper if necessary.

Open the light cover to access the wall control and safety sensor wires connected to the motor unit.

Take a digital photo of the wall control and safety sensor wires connected to the motor unit. Youll refer to the photo later when reconnecting the wires.

Disconnect the wall control and safety sensor wires from the motor unit.

Close the light cover.

Remove the nuts, bolts and lock washers that secure the motor unit to the ceiling bracket.

Support the motor unit with one hand as you remove the last bolt from the ceiling bracket.

Carefully lower the motor unit down and rest it securely on top of the step ladder.

Climb down the step ladder and lower the motor unit down to the garage floor.

Move your step ladder by the garage door so you can remove the rail from the header bracket.

Remove the fastener ring from the header bracket clevis pin.

Pull the clevis pin out of the rail and header bracket while supporting the rail with one hand.

Lower the rail to the garage floor.

Also Check: Garage Door Spring Tension Chart

The Door Operates From Wall Push Button But Not From The Transmitter

Does the battery test light glow when transmitter push button is pressed? if not, replace the battery

If you have two transmitters and only one operates. ALL transmitters must be set to same code

Is transmitter operating any other remote control devices?

Did you press the transmitter button designated to operate the garage door opener?

Reprogram receiver, and ALL transmitters Try setting ALL transmitter code switches on plus, center, or minus positions If transmitters) works, you can try a random code switch setting again, if you desire

The Door Doesnt Open Completely

$OLD – Craftsman 1/2 HP Chain Dive Garage Door Opener (2nd of 2 Available)

Is something obstructing the door?

If the door opens at least 5 feet, travel limits may need to be increased. One turn equals 2 inches of travel. REPEAT SAFETY REVERSE TEST after the adjustment is complete.

If door has been working properly but now doesnt open all the way, increase the UP FORCE. REPEAT SAFETY REVERSE TEST after the adjustment is complete.

Don’t Miss: Chamberlain Garage Door Opener With Battery Backup